679211
7
Zoom out
Zoom in
Previous page
1/44
Next page
7 GB/IE
Introduction / General power tool safety warnings
1 Quick-release chuck with SDS-plus bit system
(see Fig. A)
3 Drill bits (Ø 6 / 8 / 10 mm x 150 mm) (see Fig. B)
1 Flat chisel 250 mm (see Fig. B)
1 Pointed chisel 250 mm (see Fig. B)
1 Depth stop
50 g Special grease for lubricating the chuck
1 Carrying case
1 Set of instructions for use
Technical Data
Rated input: 1050 W
Rated voltage: 230 V∼, 50 Hz
Idle speed: n
0
0–980 rpm
BPM: 0–5300 rpm
Impact energy: 3 joules
Max. bore diameter: max. 13 mm in steel
max. 32 mm in wood
max. 26 mm in concrete
Protection class: II /
Noise emission value:
Measured sound value determined according to
EN 60745. The A-rated noise levels of the electrical
power tool are typically at:
Hammer drilling:
Sound pressure level: L
: 83.66 dB(A)
Uncertainty K: 3 dB(A)
Sound power level: L
: 94.66 dB(A)
Uncertainty K: 3 dB(A)
Chiselling:
Sound pressure level: L
: 90.62 dB(A)
Uncertainty K: 3 dB(A)
Sound power level: L
: 101.62 dB(A)
Uncertainty K: 3 dB(A)
Wear hearing protection!
Vibration total value:
The total vibration (vector sum of three directions) is
calculated in accordance with EN 60745:
Hammer drilling
into Concrete: a
h(HD)
= 8.527 m / s
2
,
K = 1.5 m / s
2
Chiselling: a
h(CHeq)
= 11.293 m / s
2
,
K = 1.5 m / s
2
The vibration level specified in
these instructions was measured in accordance with
an EN 60745 standardised measurement process
and can be used to compare equipment. The vibra-
tion emission value specified can also serve as a
preliminary assessment of the exposure.
The vibrati
on level may change with the application
of the tool and in some cases may be higher than
the value specified in these instructions. Regularly
using the electric tool in such a way may make it
easy to underestimate the vibration.
Note: If you wish to make an accurate assessment
of the vibration loads experienced during a particu-
lar period of work, you should also take into account
the intervening periods of time when the device is
switched off or is running but is not actually in use.
This can clearly reduce the vibration load through-
out the work period.
General power tool
safety warnings
Read all safety
warnings and all instructions.
Failure to follow the warnings and in-
structions may result in electric shock, fire and / or
serious injury.
Save all warnings and instructions for
future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-op-
erated (cordless) power tool.
Introduction
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PBH 1050 B2 - IAN 273100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PBH 1050 B2 - IAN 273100 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info