679211
9
Zoom out
Zoom in
Previous page
1/44
Next page
9 GB/IE
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch is
dangerous and must be repaired.
c) Pull the mains plug out of the socket
and / or remove the rechargeable bat-
tery before you make any adjustments
to the device, change accessories or
when the device is put away. This pre-
caution is intended to prevent the device from
unintentionally starting.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of un-
trained users.
e) Maintain power tools. Check for mis-
alignment or binding of moving parts,
breakage of parts and any other con-
dition that may affect the power tool’s
operation. If damaged, have the power
tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended could
result in a hazardous situation.
5. Service
a) Have your power tool serviced by a
qualified repair person using only
iden-
tical replacement parts. This will ensure
that the safety of the power tool is maintained.
Safety notes for hammer drills
Wear hearing protection!
Exposure to noise can cause hear-
ing loss.
Use the additional handle when using
the device. Losing control can lead to injury.
Hold the device by the insulated han-
dles when performing work n appli-
cations where a potential danger of
the tool striking hidden electrical lines
or its own power cable. Contact with a
live wire could cause metal parts of the device
to become live and lead to electric shock.
Wear a dust mask!
TOXIC DUST! Working on
materials which can produce harmful / toxic dusts
presents a health risk to the user and people
within close vicinity.
CAUTION - LEADS! DANGER! Verify you will
not strike electric-, gas- or water lines whilst using
the power tool. If necessary, first use a cable de
-
tector before drilling into or cutting open a wall.
Start-up
Pivot additional handle
Note: For safety reasons this device must only be
used with the additional handle
7
installed (also
see Fig. C, D, E).
The position of the additional handle
7
can be
adjusted. Turn the wing screw
1
anti-clockwise
and swivel the additional handle
7
into the
desired position.
Then tighten the wing screw
1
again.
This unit features an LED
5
. It lights up red after
connecting the device to the mains. This indicates
the device is energised and will start immediate-
ly when pressing the ON / OFF switch
3
.
General power tool safety warnings / Start-upGeneral power tool safety warnings
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PBH 1050 B2 - IAN 273100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PBH 1050 B2 - IAN 273100 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info