683959

Paladin 676 010 rf Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
GB
DE
4.- Scenes Control
Every time the pushbutton is pressed it will send a telegram type ‘Scene_Number’.
The telegram can be Scene_Load or Scene_Save.
Depending on the position of the mode selector switches it can be:
A - Brief press: the telegram ‘Scene_Load’ is sent. The number of the scene to be loaded
will be:
· POS 1: Scene 1.
· POS 2: Scene 2.
B - Sustained press (5 seconds): the telegram ‘Scene_Save’ is sent. The number of the
scene to be saved will be:
· POS 1: Scene 1.
· POS 2: Scene 2.
LINK PROCEDURE
To link the transmitter pushbutton with a compatible actuator:
1.- Place the mode selector switches in the desired mode:
2.- Set the actuator in link mode, according to the instructions given by the manufacturer.
3.- Press once the link pushbutton.
4.- Check the correct link between the two devices in the actuator, according to the
instructions given by the manufacturer.
5.- Place the mode selector switch in the desired position.
BATTERY REPLACEMENT
Release the cover of the pushbutton with the help of a screwdriver inserting it into the upper
slot.
Remove the cover of the socle and remove the batteries being careful with the components
of the printed circuit.
The pushbutton has a channel type CH_Battery_Status (Channel Code 0021h).
This additional channel allows informing to a compatible actuator with the battery status
function about this information.
When the batteries are worned-down the pushbutton will send the respective telegram and
a “battery empty” telegram each time it is pressed.
This function is optional. In order to link the pushbutton with a compatible actuator:
1.- Remove the batteries from the pushbutton.
2.- Set the KNX-RF actuator in link mode according to the instructions given by the
manufacturer.
3.- Place the batteries again in the socle.
4.- Check the correct link between the two devices in the actuator, according to the
instructions given by the manufacturer.
Switch Dimmer Blind
Switch
Scenes
4.- Szenenkontrolle
Bei Tastendruck wird der Nachrichtentyp „Scene Number“ gesendet. Die gesendete
Nachricht kann Scene_Load oder Scene_Save, sein.
Abhängig von der Position des Betriebsmodus-Schalter und der Länge des Tastendrucks
kann es sein:
A - Kurzer Tastendruck: Eine 'Scene_Load' Nachricht wird gesendet:
· P1: Scene 1
· P2: Scene 2
B - Langer Tastendruck (> 5 Sekunde): Eine 'Scene_Save' Nachricht wird gesendet:
· P1: Scene 1
· P2: Scene 2
VERLINKUNG
Um den Sensor mit einem anderen KNX-RF kompatiblen Gerät zu verlinken:
1.- Modus-Wahlschalter des 676 010 rf in die gewünschte Position bringen:
2.- KNX-RF Aktor in den Verlinkungs-Modus versetzen (siehe Bedienungsanleitung des
Aktors).
3.- Drücken Sie einmal auf die Verlinkungstaste (A).
4.- Prüfen Sie anschließend, gemäß den Angaben des Aktor-Herstellers, ob die Verlinkung
erfolgreich war.
5.- Drehen Sie den Modus-Wahlschalter in die gewünschte Funktions-Position gemäß der
oben beschriebenen Modis.
BATTERIETAUSCH
Um die Batterie zu tauschen, öffnen Sie die Abdeckung des Funktasters mittels eines
kleinen Schraubendrehers, den Sie in den oberen Schlitz drücken. Entfernen Sie die
Abdeckung und ersetzen anschließend die Batterie. Hierbei sollten Sie darauf achten, die
Leiterplatte nicht zu beschädigen.
Der Funktaster 676 010 rf hat den Kanal Typ "CH_Battery_Status" (Channel code 0021h).
Über diesen zusätzlichen Kanal kann ein Aktor angesprochen werden. Bei niedriger
Batterie-Spannung wird bei Tastendruck eine entsprechende Nachricht mit dem Daten-Typ
'battery empty' gesendet. Diese Funktion ist optional. Um den Funktaster 676 010 rf mit
einem Aktor einzurichten gehen Sie bitte wie folgt vor:
1.- Entfernen Sie die Batterie aus dem Funktaster.
2.- Aktvieren Sie den KNX-Funk-Aktor gemäß den Angaben des Herstellers.
3.- Setzen Sie die Batterie wieder ein.
4.- Überprüfen Sie die korrekte Verlinkung des Senders und des angeschlossenen
KNX-Funk-Aktors gemäß den Angaben des Herstellers.
Schalter Dimmer Rollladen-
steuerung
Szenen-
steuerung
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paladin 676 010 rf at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paladin 676 010 rf in the language / languages: English, German as an attachment in your email.

The manual is 7,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info