683968
2
Zoom out
Zoom in
Previous page
1/2
Next page
ACHTUNG!: Gefährliche Spannung!
Arbeiten am 230 V-Netz nur von Fachpersonal ausführen lassen!.
Vor Montage und Demontage Netzspannung freischalten!.
b) RF Learning Process
In order to link the paladin 673 520 rf with a wireless device follow these steps:
1. Set the channel selector (D) to the corresponding position, according to the configuration
within ETS. Choose the channel to be programmed with the RF device.
2. Set the mode selector switch (C) to position ‘P’ (link mode).
3. The LED-key (E) will flicker slowly in green.
4. Press briefly the LED-key (E). It will start flickering quickly in green. The coupler is now
ready to receive the signal from a RF-compatible paladin sensor or actuator.
5. Follow the instructions for programming the RF-compatible sensor / actuator to send its
link code.
6. If the link is successful, the LED-key (E) will light up green for two (2) seconds and then it
will return to blink slowly in green.
7. Set the mode switch (C) to 'S' (normal operation) or to 'R' (normal + repeater).
In both modes, the LED-key (E) will be in green.
b.1- Erasing a RF link (E)
In order to do a partial deletion of a link, please proceed as follows:
1. Place the mode switch (C) to ‘E’ (erase link). The LED-key (E) will light up in green
(permanent light).
2. Press briefly the LED-key (E). It will start flickering quickly in green. At this moment, the
coupler is ready to receive signal from a RF-compatible sensor or actuator.
3. Follow the instructions for deleting the RF sensor or actuator.
4. If the deletion is successful, the LED-key (E) will flash five times in red and then it will
return to light permanently in green.
b.2- RF Complete Deletion (EA: Reset)
In order to do a complete deletion, the next steps must be followed:
1. Place the mode switch (C) to ‘EA’ (Erase All). The LED-key (E) will flicker quickly in green.
2. Press the LED-key (E) for more than 4 seconds.
3. If deletion is successful, the LED-key (E) will turn green for 4 seconds and then flicker
quickly afterwards.
E.- Repeater mode
The media coupler can also act as a signal repeater.
This function is useful in the installations where are problems with the coverage between the
devices because of the distance.
It is not advisable to use more than three repeaters in the same installation.
This function is activated setting the mode selector switch to position ‘R’. The rest of
functionality continues without changes.
GB
WARNING: Hazardous voltage!.
Work with electrical equipment on the 230V mains must be carried
out only by qualified technicians!.
Switch off the mains before installing, removing or handling of
electrical equipment!.
b) RF Einlern-Prozess
Signalkoppler mit anderen RF-(KNX)-Produkten verlinken:
1. Stellen Sie den Kanalwahlschalter (D) auf den gewünschten Kanal, welcher in Ihrem
ETS-Projekt zuvor festgelegt wurde.
2. Stellen Sie den Betriebsartenwahlschalter (C) auf Position ‘P’ (Einlernmodus).
3. Die LED-Taste (E) beginnt langsam grün zu blinken.
4. Drücken Sie kurz auf die LED-Taste (E). Diese sollte nun beginnen, schnell grün zu
blinken. Der Signalkoppler ist jetzt bereit, um einen RF-(KNX)-kompatiblen Sender oder
Aktor zu verlinken.
5. Versetzen Sie den RF-(KNX) kompatiblen Sender oder Aktor in den Verlinkungsmodus
(gemäß den Vorgaben des Herstellers).
6. Sofern die Verlinkung erfolgreich war, leuchtet die LED-Taste (E) für 2 Sekunden grün auf
und wechselt anschließend in langsames blinken über.
7. Stellen Sie den Betriebsartenwahlschalter (C) auf 'S' (Normalbetrieb) oder auf 'R'
(Normalbetrieb mit zusätzlichem Verstärkermodus).
In beiden Betriebsarten sollte die LED-Taste (E) grün leuchten.
b.1- Einzelne RF-Verlinkung löschen (E)
Einzelne Verlinkung (zu einem RF-Produkt) löschen:
1. Stellen Sie den Betriebsartenwahlschalter (C) auf 'E'. Die LED-Taste (E) leuchtet nun
dauerhaft grün.
2. Drücken Sie kurz auf die LED-Taste (E). Die LED sollte nun beginnen, schnell grün zu
blinken. Jetzt ist der Signalkoppler bereit, um ein Signal eines RF-kompatiblen Senders
oder Empfängers zu empfangen.
3. Löschen Sie die Verlinkung des RF-kompatiblen Produktes gemäß den Vorgaben des
Herstellers
4. Sofern die Verlinkung erfolgreich gelöscht wurde, blinkt die LED-Taste (E) 5x rot auf und
leuchtet anschließend in grün.
b.2- Alle RF-Verlinkungen löschen (EA)
Alle Verlinkungen zu RF-(KNX)-kompatiblen Produkten löschen:
1. Stellen Sie den Betriebsartenwahlschalter (C) auf 'EA'. Die LED-Taste (E) beginnt schnell
in grün zu blinken.
2. Drücken Sie die LED-Taste (E) für mehr als 4 Sekunden.
3. Wenn alle Verlinkungen erfolgreich gelöscht wurden, leuchtet die LED-Taste (E) für 4
Sekunden grün und beginnt anschließend zu blinken.
E.- Verstärker Modus
Der Signalkoppler kann zusätzlich als Signalverstärker verwendet werden.
Diese Funktion ist besonders in Installationen hilfreich, bei denen es aufgrund einer großen
Distanz zwischen den Geräten, zu Problemen mit der Signalabdeckung kommen kann.
Beachten Sie jedoch, dass nicht mehr als drei Signalverstärker in einer Installation
verwendet werden sollten. Diese Funktion wird aktiviert, indem Sie den Betriebsart
-Wahlschalter auf „A“ stellen. Die restliche Funktionalität wird dadurch nicht beeinflusst.
DE
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paladin 673 520 rf at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paladin 673 520 rf in the language / languages: English, German as an attachment in your email.

The manual is 0,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info