683966

Paladin 673 310 rf Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
VERLINKUNG LÖSCHEN
Um eine bestehende Verbindung vom Sender (zu einem Aktor) zu löschen:
1.- Bringen Sie den Schaltaktor in den Entkopplungs-Modus, gemäß den Angaben des
Herstellers.
2.- Drücken Sie kurz die Verlinkungstaste (C) am Sender. Die rote LED blinkt schnell.
3.- Sofern die Entkopplung erfolgreich war, blinkt die grüne LED einmal kurz auf und
leuchtet anschließend.
Sollte die Entkopplung nicht erfolgreich sein, versucht das Gerät ein zweites Mal die
Verbindung zu trennen. Falls dies ebenfalls fehlschlägt, blinkt die rote LED erneut (1x)
und das Gerät beendet den Verlinkungsmodus. Die grüne LED leuchtet nun.
4.- Überprüfen Sie gemäß den Anweisungen des Herstellers des Aktors, ob die Verbindung
zwischen den beiden Geräten ordnungsgemäß getrennt wurde.
VERSTÄRKER MODUS
Der Sender kann zusätzlich als Signalverstärker verwendet werden.
Diese Funktion ist besonders in Installationen hilfreich, bei denen es aufgrund einer
großen Distanz zwischen den Geräten, zu Problemen mit der Signalabdeckung kommen
kann.
Beachten Sie jedoch, dass nicht mehr als drei Signalverstärker in einer Installation
verwendet werden sollten.
Um die Funktion zu aktivieren, drücken Sie die Verlinkungs-Taste (C) für mehr als eine
Sekunde bzw. bis die rote LED leuchtet. Die restliche Funktionalität wird dadurch nicht
beeinflusst.
Sofern aktiviert, kann die Funktion mittels Drücken der Verlinkungs-Taste (C) für länger als
eine Sekunde (bis die rote LED ausgeht und die grüne LED leuchtet) wieder deaktiviert
werden.
DE
DELETION PROCEDURE
In order to delete an existing link (to an actuator) from the temperature sensor:
1.- Set the RF actuator in unlink mode according to the instructions given by the
manufacturer.
2.- Press the link / unlink key (C) briefly. The red LED will flash once fast, which means that
the linking code has been sent.
3.- If the unlink process was successful, the green LED will flash once and will then be on.
If the first unlinking attempt failed, the Paladin 673 310 rf will try a second time.
If the second attempt fails also, the device will show it by flashing the red LED once and
then return to normal operation mode with the green LED on.
4.- Check the successful unlink between the two devices in the actuator, according to the
instructions given by the manufacturer.
REPEATER MODE
The Paladin 673 310 rf can also act as a signal repeater.
This function is useful in the installations where are problems with the coverage between the
devices because of the distance.
It is not advisable to use more than three repeaters in the same installation.
This function is activated by pressing the link key (C) for more than 1 second, until the red
LED is on.
While this function is active, the rest of the functionality of the 673 310 rf remains
unchanged.
To disable this function, press the link button (C) for more than 1 second. The red LED will
turn off and the green LED will be on.
GB
A
E
C
F
D
B
G
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paladin 673 310 rf at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paladin 673 310 rf in the language / languages: English, German as an attachment in your email.

The manual is 3,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info