683966
1
Zoom out
Zoom in
Previous page
1/2
Next page
GB
WIRELESS TEMPERATURE SENSOR
TECHNICAL DATA
DESCRIPTION
The Paladin 673 310 rf is a wireless temperature sensor, including the following
components:
· Transmitter (A): captures the value from the temperature probe and transmits it via RF to
the linked receiver.
· Temperature probe (B): measures the temperature sensed at the tip of the probe. Must be
connected directly to the transmitter via its original cable, which is double insulated. Tip
of the probe is waterproof.
The transmitter has a link button (C). This button is used to link device to other compatible
devices or to select Repeater mode.
The Transmitter has two wires (D) for connection to the mains.
Avoid installation close to radioelectric devices, microwaves, ...
A minimum distance of 2m must be maintained between the sensor and the linked actuator.
WARNING: Hazardous voltage!
· Work with electrical equipment on the 230V mains must be carried out only by
qualified technicians!
· Switch off the mains before installing, removing or handling electrical equipment!
INSTALLATION
The Transmitter has two wires, blue (N) and black (L), in order to supply the device with
230V.
Before switching on the power, connect the temperature probe to the two-fold terminal
connector (F) on the transmitter.
There is also a white wire, which is the antenna and must not be connected to any potential
or signal.
This wire should be in an extended position to achieve maximum coverage.
OPERATION
The Paladin 673 310 rf transmits the temperature depending on the position of the switch
(G) in two different ways:
- In position (1) temperature value is sent every minute.
- In position (2) temperature value is sent every 5 seconds.
The device has an integrated RF signal repeater function, which can be activated or
deactivated depending on the needs.
LINK PROCEDURE
To link the temperature sensor with a compatible KNX-RF actuator:
1.- Set the RF actuator in link mode according to the instructions given by the
manufacturer.
2.- Press the link key (C) briefly. The red LED will flash once fast, which means that the
linking code has been sent.
3.- If the linking process was successful, the green LED will flash once and will then be on.
If the first linking attempt failed, the Paladin 673 310 rf will try a second time. If the
second attempt fails also, the device will show it by flashing the red LED once and then
return to normal operation mode with the green LED on.
4.- Check the correct link between the two devices in the actuator, according to the
instructions given by the manufacturer.
NOTICE: In order to install the device correctly, its connections must be installed to
connecting devices (or connection terminals) which fulfill with the Standards
EN 60998-1, EN 60998-2-1 or EN 60998-2-2.
Protection degree IP20
Working temperature 0ºC ~ +45ºC
Dimensions 45 x 43 x 12mm
Radio-Frequency
Codified transmission in 868,3MHz
Range: 100m (in the free field)
Compatible with KNX-RF: CC_Temperature
Measurement accuracy
+/- 1ºC
Minimum Temperature
-20ºC
Maximum Temperature
+55ºC
Sending frequency
1 minute
Probe Maximum Length
5m (included 3m length wire)
Probe Material Epoxy
Consumption ~25mA @ 230V
Power supply 230V~ 50Hz
673 310 rf
Schutzart IP20
Betriebstemperatur 0ºC ~ +45ºC
Abmessungen 45 x 43 x 12mm
Funkfrequenz
Verschlüsselte Übertragung, 868,3MHz
Reichweite: 100 m (auf freiem Feld)
Kompatibel mit KNX-RF: CC_Temperature
Messgenauigkeit
+/- 1ºC
DE
FUNK-TEMPERATURSENSOR MIT EXTERNEM FÜHLER
TECHNISCHE DATEN
BESCHREIBUNG
Funk-Sender mit externem Temperaturfühler bestehend aus folgenden Komponenten:
· Sender (A): Übermittelt den gemessenen Wert vom externen Fühler per Funk an den
verlinkten Empfänger.
· Externer Temperaturfühler (B): Messung der Temperatur. Muss direkt mit dem Sender
verbunden werden. Das Kabel ist zweifach isoliert und hat einen wassergeschützten
Messfühler.
Mittels Verlinkungstaste (C) kann eine Verlinkung zu kompatiblen Geräten hergestellt, bzw.
der Verstärker-Modus aktiviert werden.
Es befinden sich zwei Leitungen am Sender zum Anschluss an die Spannungsversorgung.
Installation in der Nähe von Feuchtigkeit oder Hitzequellen vermeiden.
Mindestabstand von 2 Metern zwischen Sender und Empfänger bzw. Repeater einhalten.
WARNUNG!: Gefährliche Spannung!
· Arbeiten am 230 V-Netz nur von Fachpersonal ausführen lassen.
· Vor Montage und Demontage Netzspannung freischalten!
INSTALLATION
Der Sender hat zwei Anschlussleitungen, 1x Blau (N) und 1x Schwarz (L), um das Gerät mit
der Spannungsversorgung (230V) zu verbinden.
Zuvor den externen Temperaturfühler an die 2-fach Klemme (F) anschließen.
Zusätzlich befindet sich eine weiße Litze am Gerät, die als Funk-Antenne dient. Diese darf
unter keinen Umständen an irgendwelche Potentiale angeschlossen werden.
Um die Reichweite zu maximieren, sollte die Antenne ausgestreckt platziert werden.
BETRIEB
Die Temperatur wird vom Sender je nach Stellung des Schalters (G) wie folgt übertragen:
- Position (1): Übertragung jede Minute.
- Position (2): Übertragung alle 5 Sekunden.
Zusätzlich kann bei Bedarf im Gerät die Repeater-Funktion aktiviert werden (siehe
Verstärker-Modus).
VERLINKUNG
Um den Sender mit einem KNX-RF kompatiblen Aktor zu verbinden gehen Sie bitte
folgendermaßen vor:
1.- Bringen sie den KNX-Funk-Aktor in Linkbereitschaft, gemäß den Angaben des
Herstellers.
2.- Drücken Sie kurz auf die Verlinkungstaste (C) des Senders. Die rote LED blinkt einmal
kurz auf.
3.- Wenn die Verbindung erfolgreich war, blinkt die grüne LED einmal kurz auf und leuchtet
anschließend.
Sofern die Verbindung nicht erfolgreich sein sollte, versucht das Gerät ein zweites Mal
die Verbindung herzustellen.
Sollte dies ebenfalls fehlschlagen, blinkt die rote LED erneut (1x) und das Gerät
beendet den Verlinkungsmodus. Die grüne LED leuchtet nun.
4.- Überprüfen Sie gemäß den Anweisungen des Herstellers des Aktors, ob die Verbindung
zwischen den beiden Geräten ordnungsgemäß hergestellt wurde.
Bemerkung: Für die korrekte Installation des Geräts müssen Verbindungsstücke bzw.
-klemmen verwendet werden welche die Normen EN 60998-1, EN 60998-2-1 oder
EN 60998-2-2 erfüllen.
Leistungsaufnahme ~25mA @ 230V
Anschlussspannung 230V~ 50Hz
L
N
230V~ 50Hz
L
N
Minimaler Messbereich
-20ºC
Maximaler Messbereich
+55ºC
Übertragungszyklus
1 Minute
Maximale Kabellänge Fühler
5m (mitgelieferter Fühler: 3m Kabel)
Material des Fühlers
Epoxid
A
E
C
F
D
B
G
1
2
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paladin 673 310 rf at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paladin 673 310 rf in the language / languages: English, German as an attachment in your email.

The manual is 3,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info