683956
2
Zoom out
Zoom in
Previous page
1/2
Next page
COMMISSIONING
P.- Programming a link
To link the receiver channel of the Thermostat with the sender channel of other
compatible RF-KNX device (sensor temperature, door/window contact, presence
detector...):
1.- Set the mode selector switch (D) at “P” position. The red LED will flicker slowly.
2.- Press the configuration pushbutton (A) until the LED starts flickering quickly. The
receiver channel of the Thermostat is now waiting to accept a link from the
transmitter channel of the other RF-KNX device.
3.- Set thetransmitter channel of the other RF-KNX device in “link programming mode”
according to the instructions given by the manufacturer.
4.- If the link is successful the LED of the Thermostat will be on for 5sec and then it
will flicker slowly again. If the link is not successful the Thermostat will leave
automatically the programming mode and the LED will flicker slowly. In the same
way, 1 minute after the Thermostat is in programming mode without no attempt to
link a sender channel from other device it will leave this mode automatically and the
LED will flicker slowly.
5.- To become the Thermostat operational would be necessary to set the mode
selector switch at “F” position.
B.- Delete a link
To delete a link with other RF transmitter from the receiver channel of the Thermostat:
1.- Set the mode selector switch at ‘B’ position. The LED will flicker slowly.
2.- Press the configuration key with help of a clip. The LED will flicker quickly. The
receiver channel of Thermostat is waiting to receive the signal from the sender
channel of the other device we want to unlink.
3.- Set the sender channel of the device we want to unlink in programming mode
according to the instructions given by the manufacturer.
4.- If the unlink is successful the LED will be on for 5 seconds and then will flicker
slowly.
If the unlink is not successful the Thermostat will leave automatically the programing
mode and the LED will flicker slowly. In the same way, 1 minute after the
Thermostat is in programming mode without no attempt to unlink a sender channel
from other device it will leave this mode automatically and the LED will flicker slowly.
5.- To become the Thermostat operational set the mode selector switch at ‘F’ position.
R.- RESET: Delete all links
To delete all links from the Thermostat:
1.- Set the mode selector switch in RESET (’R’). The LED will flicker slowly.
2.- Press the configuration pushbutton with a clip. The LED will flicker quickly.
3.- Keep on pressing for 5sec. until the LED flickers slowly.
4.- To become the Thermostat operational set the mode selector switch over ‘F’.
A.- Repeater mode
The Thermostat switch can also act as a signal repeater.
This function is useful in the installations where are problems with the coverage between
the devices because of the distance.
It is not advisable to use more than three repeaters in the same installation.
This function is activated setting the mode selector switch in ‘A’. The rest of functionality
continues without changes.
Notes:
· It is not advisable to use more than 3 repeaters in the same installation.
· It is not advisable to use repeaters if it is not really necessary.
INBETRIEBNAHME
P.- Verlinken des Empfängerkanals
Um den Empfängerkanal des Schaltaktors mit dem Senderkanal eines anderen
RF-(KNX)-Gerätes zu verlinken (Temperatur-Sensor, Tür-/Fensterkontakt oder
Präsenzmelder,...):
1.- Betriebsart -Wahlschalter (D) auf Position „P“ stellen. Die rote LED blinkt langsam.
2.- Einlerntaste (A) mit Hilfe einer Büroklammer oder etwas ähnlichem drücken. Die
LED blinkt schnell. Der Empfängerkanal des Schaltaktors wartet nun darauf, die
Verbindung mit dem Senderkanal eines anderen RF-(KNX)-Gerätes herzustellen.
3.- Senderkanal des gewünschten RF-(KNX)-Gerätes in den Verlinkungsmodus stellen
(gemäß den Vorgaben des Herstellers).
4.- Wenn die Verbindung erfolgreich war, leuchtet die LED 5 Sekunden lang auf und
blinkt danach langsam.Wenn die Verbindung nicht erfolgreich war, wird der
Schaltaktor automatisch den Programmier-Modus verlassen, die rote LED beginnt
danach wieder langsam zu blinken.Sollte es für 1 Minute keine Verlinkungsver-
suche geben, verlässt der Schaltaktor ebenfalls den Programmier-Modus, die rote
LED beginnt danach wieder langsam zu blinken.
5.- Der Schaltaktor ist betriebsbereit sobald Sie den Betriebsart -Wahlschalter nach
erfolgreichem Pairing auf die Position „F“ stellen.
B.- Verlinkung des Empfängerkanal löschen
Um eine Verlinkung zwischen Funk-Sendern und dem Empfängerkanal des Schaltaktors
zu löschen:
1.- Stellen Sie den Betriebsart -Wahlschalter des Schaltaktors auf Position „B“. Die
LED blinkt langsam.
2.- Einlerntaste mit Hilfe einer Büroklammer oder etwas ähnlichem drücken. Die LED
blinkt schnell. Der Empfängerkanal des Schaltaktors wartet nun auf das Signal von
dem Senderkanal des anderen Geräts.
3.- Stellen Sie nun den Senderkanal des anderen Geräts in den „entkoppeln“-Modus
(gemäß den Vorgaben des Herstellers).
4.- Wenn das Löschen der Verbindung erfolgreich war, leuchtet die LED 5 Sekunden
lang auf und danach blinkt die LED langsam. Wenn das Löschen der Verbindung
nicht erfolgreich war verlässt der Aktor automatisch den Modus und die LED blinkt
langsam. Sollte es für 1 Minute keine Versuche geben die Verlinkung zu löschen,
verlässt der Schaltaktor ebenfalls den Programmier-Modus, die LED blinkt langsam.
5.- Der Schaltaktor ist betriebsbereit sobald Sie den Betriebsart -Wahlschalter auf die
Position „F“ stellen.
R.- RESET: Verlinkungen aller Empfänger- und Senderkanäle löschen
Um alle Verlinkungen des Schaltaktors zu löschen:
1.- Betriebsart -Wahlschalter auf Position „R“ (RESET) stellen. Die LED blinktlangsam.
2.- Einlerntaste mit Hilfe eines Clips oder etwas ähnlichem drücken bis die LED schnell
blinkt.
3.- Halten sie weiter gedrückt bis die LED langsam blinkt.
4.- Der Schaltaktor ist betriebsbereit sobald Sie den Betriebsart -Wahlschalter auf die
Position „F“ stellen.
A.- Verstärker Modus
Der Schaltaktor kann zusätzlich als Signalverstärker verwendet werden.
Diese Funktion ist besonders in Installationen hilfreich, bei denen es aufgrund einer
großen Distanz zwischen den Geräten zu Problemen mit der Signalabdeckung kommen
kann. Beachten Sie jedoch, dass nicht mehr als drei Signalverstärker in einer Installation
verwendet werden sollten. Diese Funktion wird aktiviert, indem Sie den Betriebsart
-Wahlschalter auf „A“ stellen. Die restliche Funktionalität wird dadurch nicht beeinflusst.
Bitte beachten:
· Beachten Sie das nicht mehr als drei Signalverstärker in einer Installation verwendet
werden sollten.
· Es ist nicht ratsam den Verstärker Modus zu nutzen, wenn er nicht benötigt wird.
EN DE
A A
R
P
F
A
B
ºc
5
10
15
20
25
30
ºc
5
10
15
20
25
30
R
P
F
A
B
R
P
F
A
ºc
5
10
15
20
25
30
A
B
2 31
A
ºc
5
10
15
20
25
30
A
R
P
F
A
B
ºc
5
10
15
20
25
30
4
A
R
P
F
A
B
ºc
5
10
15
20
25
30
5
A
R
P
F
A
B
ºc
5
10
15
20
25
30
2 31 4 5
R
P
F
A
ºc
5
10
15
20
25
30
A
B
A
R
P
F
A
B
ºc
5
10
15
20
25
30
A
ºc
5
10
15
20
25
30
R
P
F
A
B
R
P
F
A
ºc
5
10
15
20
25
30
A
B
2 31
R
P
F
A
B
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paladin 672 731 rf at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paladin 672 731 rf in the language / languages: English, German as an attachment in your email.

The manual is 0,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info