608263
15
Zoom out
Zoom in
Previous page
1/16
Next page
15
Troubleshooting guide
The following guide lists problems which do not require professional servicing. If, however, the problem cannot be remedied using this
guide, contact an ONKYO authorized service center for assistance.
• No power.
Cause: Power cord plug is loose
Remedy: Insert plug properly into outlet.
• Playback but no sound.
Cause: Incorrect connection.
Remedy: Check and connect correctly according to page
5.
Cause: Stereo amplifier input selector switch is set to
incorrect position.
Remedy: Change switch position.
• Tape does not move.
Cause: Slack tape wound around pinch roller.
Remedy: Take up slack with a pencil (see page 13).
t button does not engage.
Cause: No tape in cassette holder.
Remedy: Insert cassette tape.
Cause: Erasure prevention tab(s) removed.
Remedy: Change cassette or cover tab hole with
cellophane tape.
• Hoarse sound, balance unstable.
Cause: Playback head dirty.
Remedy: Clean head (see page 14).
Cause: Tape is stretched.
Remedy: Replace cassette.
• Excessive noise and tape hiss.
Cause: Head has become magnetized.
Remedy: Demagnetize (see page 14).
Cause: Tape with high noise level.
Remedy: Replace cassette.
• Distorted sound.
Cause: Distortion in tape.
Remedy: Tape is probably bad but confirm by listening to
another.
• Recordings are distorted.
Cause: Recording was done at too high a level.
Remedy: Readjust REC LEVEL knob according to the
directions on page 8.
• Tape squeal and skipping.
Cause: Dirty heads, pinch rollers or capstan shafts.
Remedy: Clean (see page 14).
Cause: Cassette shell is binding tape or tape is stretched.
Remedy: Change cassette or try correcting with fast
forward and rewind.
• Excessive hum during playback.
Cause: Connecting cables not inserted firmly.
Remedy: Insert plugs firmly.
Cause: External flux leakage from nearby amplifier or TV
set.
Remedy: Move deck away from hum source.
• High frequencies too strong.
Cause: Dolby NR encoded tape played back with NR off.
Remedy: Select the same noise reduction (Dolby NR B or
C) used when the cassette was recorded.
Cause: Incorrect equalization.
Remedy: Confirm that cassette has tape type detection
holes.
• No high frequency sounds.
Cause: Tape not encoded with Dolby NR played back with
Dolby B or C NR on.
Remedy: Select the appropriate NR mode using the
DOLBY NR button (OFF).
Cause: Heads have become dirty.
Remedy: Clean (see page 14).
• The skip function does not operate properly.
Cause: The silent sections between songs are too short or
noisy.
Remedy: Use a cassette with sufficiently silent sections of
sufficient length between songs.
• Deck does not operate properly.
Cause: Tape transport control microcomputer has been
exposed to interference from power supply or static
electricity.
Remedy: Press the POWER button to turn off the power.
Wait approximately 10 seconds and turn it on
again.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TA-RW244 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TA-RW244 in the language / languages: English as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info