569260
3
Zoom out
Zoom in
Previous page
1/3
Next page
Remedying a paper jam
If too much paper is fed into the cutting unit, a paper jam occurs.
Proceed as follows:
- Push the sliding switch to the REV position.
- The cutting unit runs backwards and pushes the excess paper back.
- Reduce the paper quantity and slide the switch to ON/AUTO again. The cutting unit
runs forward again and the paper still in the cutting unit is shredded.
If the backwards and forwards movement does not remedy the paper jam, pull out the
mains plug and remove the remaining paper manually from the cutting unit.
Motor protection
The motor switches off automatically in the event of overloading. Pull out the mains
plug from the socket and allow the motor to cool down to room temperature. Plug the
mains cable back in and then continue operation.
Notes on care and maintenance
Caution: maintenance work may only be performed when the mains plug is pulled
out.
For you to be able to continue using your paper shredder for as long as possible, clear
residual paper from the cutting unit at regular intervals and apply special oil for paper
shredders to the cutting unit. This special oil is available from specialist dealers or di-
rectly from our service centre in Hattingen. This will extend the service life of the device.
Technical data
Model: PS-35CC
Power supply: 230V / 50Hz
Cutting width: 4 x 40 mm (cross-cut particles)
Cutting power: max. 3 DIN A4 sheets (70 g/m
2
)
Security level: 3
Max. power consumption: 0.8 A
Size (W x H x D): 302 x 312 x181 mm
Weight: 3288 g
Device malfunctions
Problem Cause Remedy
Is the mains cable plugged
properly in the socket?
Plug the mains cable into the
socket properly.
Is the sliding switch set to
ON/AUTO?
Set the sliding switch to ON/AUTO.
Does the motor not start
when paper is fed in?
Push the paper into the infeed slot
so that it touches the sensor in the
centre.
Device does not
work
Has the device been placed
the right way round and in
the correct position on the
paper collection basket?
Place the device on properly so
that the contact switch is activated.
Problem Cause Remedy
Device does not
work after lengthy
operation or
stops during
operation
Was the device in constant
operation for some time?
Is the surface of the device
warm?
Pull out the mains plug from the
socket and allow the motor to cool
down to room temperature.
Paper jam Have you inserted more
than 3 sheets of paper (70
g/m²)?
Has the paper not been
inserted straight in the in-
feed slot?
Set the sliding switch to REV to
push back the paper. Switch the
device to ON/AUTO again to shred
the paper remaining in the cutting
unit.
If you cannot rectify the fault yourself, contact your dealer or call the Olympia hotline.
Guarantee
ATTENTION!
INPORTANT GUARANTEE DOCUMENTS
PLEASE STORE IN A SAFE PLACE.
Dear Customer,
Thank you for buying a quality product from
. In the unlikely event that
the device should develop a technical problem please observe the following
points:
¾ The guarantee period for the device is 24 months.
¾ Make sure that you store the purchasing receipt and the original packaging.
¾ Should a problem occur, please call our hotline first:
+ 49 (0) 180/500 7514
(Fee for connections outside Germany: additional Euro 0.12
per call for the connection within Germany.)
Our personnel are often able to provide helpful advice over the phone.
¾ If it is not possible to clear up the problem over the phone, please send the
device back to the following address:
Service-Center Hattingen
Weg zum Wasserwerk 10
45525 Hattingen, Germany
Guarantee repairs will only be performed if the purchase receipt is enclosed with
the device.
Thank you for your understanding.
Yours faithfully,
Your Olympia Business Systems partner
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Olympia PS-35CC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Olympia PS-35CC in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Olympia PS-35CC

Olympia PS-35CC User Manual - German - 3 pages

Olympia PS-35CC User Manual - Dutch - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info