618128

Numark Mixtrack Pro II Manual

6
Zoom out
Zoom in
Previous page
1/28
Next page
6
PAD MODE COMMANDS
The lower row of pads has different functions depending on their mode: Looping Mode, Sample Mode, or Hot
Cue Mode.
To select a mode, hold down the SHIFT button and press one of the lower pads. An LED under
the pad section indicates the currently selected mode.
Looping Mode: Press Shift + Loop In to assign the lower 4 pads to the functions listed below:
• Loop In – Sets the beginning of a loop. After a Loop Out point is set, when this button is pressed again, it
will allow for fine adjustment of the Loop In point.
• Loop Out – Sets the end point for the loop. When this button has been pressed after a Loop Out point has
been set, it will allow for fine adjustment of the Loop Out point.
• Reloop – When this is pressed inside a loop, this will turn the loop off. When pressed outside a loop, this
will activate the loop and start playback from its Loop In point. If a loop has not been set, this button will
have no effect.
• Loop x1/2 – Cuts the currently playing loop in half. Press Shift + Loop x1/2 to double the length the
currently playing loop.
Sample Mode: Press Shift + Loop Out to assign the lower 4 pads to the functions listed below:
• Sample 1 (S1) – Plays the sample assigned to Sample Pad 1.
• Sample 2 (S2) – Plays the sample assigned to Sample Pad 2.
• Sample 3 (S3) – Plays the sample assigned to Sample Pad 3.
• Sample 4 (S4) – Plays the sample assigned to Sample Pad 4.
Hot Cue Mode: Press Shift + Reloop to assign the lower 4 pads to the functions listed below:
• Cue 1 (C1) – If a cue point has not already been set for the loaded track, this control will mark Cue Point
1. If a cue point has already been set, this control will jump to Cue Point 1.
• Cue 2 (C2) – If a cue point has not already been placed on the loaded track, this control will mark Cue
Point 2. If a cue point has already been set, this control will jump to Cue Point 2.
• Cue 3 (C3) – If a cue point has not already been placed on the loaded track, this control will mark Cue
Point 3. If a cue point has already been set, this control will jump to Cue Point 3.
• Delete Cue (C) – Press this button, and then press one of the other pads in the row to delete its cue point.
SIDE PANEL
1. Headphone Output – Connect headphones to these 1/4”
and 1/8” jacks for monitoring the signal. The headphone
volume is controlled using the Cue Gain knob.
2. Microphone Input – Connect a standard dynamic
microphone to this 1/4” jack.
3. Mic Gain – Adjusts the level for the microphone input.
REAR PANEL
1. Master Output (RCA) – Use standard RCA cables to connect
this output to a speaker or amplifier system.
2. USB – Sends USB MIDI data to control various software
parameters.
1
2
2
3
1
1
2
2
3
1
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Numark Mixtrack Pro II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Numark Mixtrack Pro II in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 7,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info