609460

Nilfisk-ALTO SCRUBTEC R 466 Manual

91
Zoom out
Zoom in
Previous page
1/124
Next page
USER MANUAL
ENGLISH
9098960000(1)2011-04 A SCRUBTEC R 466 - R 471 - R 471C - BOOST
®
R4 29
TROUBLESHOOTING
TROUBLE POSSIBLE CAUSE REMEDY
The motors do not work; no warning light turns on.
The battery connector is disconnected. Connect.
The batteries are discharged. Charge the batteries.
The machine does not move and the display (71)
shows the error code:
The machine has been turned on by using the
ignition key and by keeping the pedal pressed.
Release the drive pedal.
If the problem persists, contact an authorised
Service Center.
At the machine start-up, the LED (64) of the
switch (63) fl ashes and the brushes do not work.
The machine has been turned off without
lifting the brush deck.
Wait for the deck to lift before turning on again
the brushes by pressing the switch.
The brushes do not work; the red warning light
fl ashes.
The batteries are discharged. Charge the batteries.
The 3 warning lights (62) fl ash simultaneously.
The brush motors are overloaded.
Use less aggressive brushes and/or avoid
working with extra pressure turned on.
There are foreign materials (tangled threads,
etc.) preventing the brushes from rotating.
Clean the brush hubs.
The display (71) shows an error code as:
where “00” is replaced by a code different from
“t4”.
The machine electronic control system is in
alarm condition.
Turn off the machine and then turn it on again.
If the problem persists, contact an authorised
Service Center.
The dirty water vacuuming is insuffi cient.
The recovery tank is full. Empty the tank.
The vacuum grid is clogged or the fl oat is
closing.
Clean the vacuum grid.
The container with debris collection grid is
clogged.
Clean.
The hose is disconnected from the squeegee. Connect.
The squeegee is dirty, or the squeegee blades
are worn or damaged.
Clean the squeegee or overturn/replace the
blades.
The tank cover is not properly closed, or the
gasket is damaged.
Correctly close the cover or clean/replace the
gasket.
The solution fl ow is insuffi cient.
The solution tank is empty. Refi ll.
The solution fi lter is dirty. Clean the fi lter.
The Chemical Mixing System tank (optional)
is dirty/clogged.
Clean with the drain cycle.
The squeegee leaves marks on the fl oor.
There are debris under the squeegee blades. Remove the debris.
The squeegee blades are worn, chipped or
torn.
Overturn or replace the blades.
The squeegee is not balanced with the
handwheel.
Adjust the squeegee.
NOTE
If the machine has a battery charger installed, the machine cannot operate if the charger is not on board. In case of
battery charger malfunction, contact an authorised Service Center.
For further information, contact Nilfi sk Alto Service Centers.
9098960000(1)2011-04 A.indb 299098960000(1)2011-04 A.indb 29 07/04/2011 15:59:2307/04/2011 15:59:23
… 91 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nilfisk-ALTO SCRUBTEC R 466 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nilfisk-ALTO SCRUBTEC R 466 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info