Manual Niko 350-20065 (page 10 of 12) (English, German, Dutch, French)

619206

Zoom out

Zoom in

1/12

nv Niko sa Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.be — www.niko.eu PM350-20065R12235

350-20065

5. MAINTENANCE

Dirt may prevent the presence detector from functioning properly. Therefore, always keep the lens clean and

dry. Use a damp cloth and water with some detergent to clean the lens. Never exert pressure to wipe the lens

clean. If the lens or other parts of the presence detector are defective, please contact an authorised installer.

6. TROUBLESHOOTING

Problem Cause Action

The lighting is not switched on. Incorrect wiring. Refer to the wiring diagrams and

check if the lighting is working.

The ambient light level is too

high.

Check the set lux value and

adjust if necessary (higher value).

The lighting is not switched off. The switch-off delay is too long. Check the switch-off delay and

adjust if necessary (lower value).

Detector has false triggering. Check for any objects in the room

that may cause false triggering

and remove them from the

detection area.

Incorrect wiring. Check the wiring diagrams.

The red LED does not turn on. PIR is not selected as the

detection method.

Select PIR as the detection

method.

The movement is outside the

detection range of the PIR sensor.

The movement should be within

the detection range (8 m).

A cover cap is used so that there

is no detection on the place of the

movement.

Remove or reposition the cover

cap.

The green LED does not turn on. US is not selected as the

detection method.

Select US as the detection

method.

The movement is outside the

detection range of the ultrasonic

sensor.

The movement should be within

the detection range (10 x 16 m).

False triggering The following elements may

affect the proper functioning of

the ultrasonic sensor and may

cause false triggering:

- air ﬂows

- sound absorbing materials,

carpet, curtains, …

- heat sources

- reﬂective objects

- objects subject to wind

- wiring (a reverse wiring between

N and L will cause reduced

sensitivity of the ultrasonic

sensor sensitivity and will limit

the detection area)

- Activate the potentiometer for

light sensitivity (ON). This will

reduce the sensitivity of the

ultrasonic sensor by ± 10 to

40%, depending on the severity

of the air ﬂow.

- Avoid aiming the detector

toward any heat sources, such

as air conditioning, electric fans,

heaters or reﬂective surfaces.

- Make sure there are no objects

within the detection range that

are subject to wind.

- Check the wiring diagrams.

7. TECHNICAL DATA

dimensions 60 x 120 mm (HxW)

power supply voltage 230 Vac ± 10%, 50 Hz

power consumption 1 W

relay contact NO (max. 10 A, 230 V), potential-free, light- and

motion-sensitive

maximum load incandescent lamps (2300 W)

230 V halogen lamps (2300 W)

all low-voltage halogen lamps (2300 W)

fluorescent lamps (non-compensated) (1200 VA)

economy lamps (CFLi) (58 x 18 W)

maximum switching capacity 140 μF

maximum inrush current 165 A/20 ms

detection angle 360°

mounting height 2 – 3 m

detection range US: 10 x 16 m (138 m²)

PIR: ø 8 m (50 m²)

light sensitivity 10 – 1000 lux

switch-off delay 1 – 30 min

protection degree IP20

protection class class I devices

ambient temperature 0 – 45°C

cable inlet 2 x 12 mm

quality mark CE marked in compliance with EN 60669-2-1

accessories IR remote control (350-20067)

8. WARNINGS REGARDING INSTALLATION

- The installation should be carried out by a registered installer and in compliance with the statutory

regulations.

- This user manual should be presented to the user. It should be included in the electrical installation ﬁle, and

it should be passed on to any new owners. Additional copies are available on the Niko website or via the

Niko support service.

- During installation, the following should be taken into account (non-exhaustive list):

- the statutory laws, standards and regulations.

- the technology currently available at the time of installation.

- this user manual, which only states general regulations and should therefore be read within the scope of

each speciﬁc installation.

- the rules of proper workmanship.

9. NIKO SUPPORT

In case of doubt or for the speciﬁc exchange procedure in case of a possible defect, contact the Niko support

service in Belgium at +32 3 778 90 80 or your wholesaler/installer. Contact details and more information can

be found at www.niko.eu under the “Help and advice” section.

10. GUARANTEE PROVISIONS

- The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of

purchase of the product by the consumer. If there is no invoice, the date of production applies.

- The consumer is obliged to inform Niko in writing about the non-conformity, within two months after stating

the defect.

- In case of a non-conformity, the consumer only has the right to a product repair or replacement free of

charge, which shall be decided by Niko.

- Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or

careless use, incorrect operation, transformation of the product, maintenance that does not adhere to the

maintenance instructions or an external cause, such as damage due to moisture or overvoltage.

- The compulsory regulations of the national legislation concerning the sale of consumer goods and the

protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries,

chain stores, distributors, agents or permanent sales representatives, take priority over the above-

mentioned rules and regulations.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Niko 350-20065 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5,71 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Niko 350-20065 Manual

Product: