519647

Netgear WN111v2 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
May 2008
This symbol was placed in accordance with the European Union Directive
2002/96 on the Waste Electrical and Electronic Equipment (the WEEE
Directive). If disposed of within the European Union, this product should be
treated and recycled in accordance with the laws of your jurisdiction
implementing the WEEE Directive.
© 2008 by NETGEAR, Inc. All rights reserved. NETGEAR and the NETGEAR logo are registered trademarks
of NETGEAR, Inc. in the United States and/or other countries. Other brand and product names are trademarks or
registered trademarks of their respective holders. Information is subject to change without notice.
Using the Status Bar
1. For connection details, check the status bar, located at the bottom of the Settings tab.
Understanding the Status Bar
Wireless network Identifies which wireless network you have joined.
Security • A closed lock indicates that security is enabled.
• An open lock indicates an open network without wireless security.
Channel The wireless channel used by the network. If many wireless
networks in your area use the same channel, they can interfere with
one another.
Data rate Wireless data rate measured in Megabits per second. To optimize
wireless data rate, connect to a network with a high-speed router or
access point and a high-speed Internet connection.
Signal strength More dots indicates a stronger signal. Usually, you experience
higher throughput when the signal is strongest.
Join a Network Click Join a Network to start the Connection Wizard.
Wireless
network
Connection status
Security
Join a Network
Channel
Data rate
Signal
strength
2. When you are finished reviewing the Settings tab, click Close.
You can use the icon at any later time to access your adapter settings. For
information about all settings available for your wireless adapter, refer to the
NETGEAR RangeMax™ Wireless-N USB 2.0 Adapter WN111v2 User Manual on the
Resource CD.
Using the USB Cable and Cradle
You can attach the wireless USB adapter directly to a USB port on your computer, or use
the USB cable to extend the range and obtain better wireless reception. Use the USB
cable, plastic cradle, and loop-and-hook fastener for better adapter placement on a
computer monitor.
1. Attach the first fastener.
The wireless USB adapter comes with three black
fasteners. Locate the one with a prickly side, and attach it
to the plastic cradle on the middle of the outside
rear.Insert the adapter in the plastic cradle.
2. Connect the USB cable.
3. Place the other fasteners.
Place one of the other pieces of loop-
and-hook fastener on the side or back of
your monitor near the top for better
reception.
Connection
status
The status of your network connection.
• Connected to Internet. The wireless Internet connection is OK.
• Connected to Router. The wireless connection to the router is
OK, but the router is not connected to the Internet.
• 169.254.x.x or ___.___.___.___ . The wireless connection to the
router is OK, but there is a problem with the router. See the
NETGEAR RangeMax™ Wireless-N USB 2.0 Adapter WN111v2
User Manual on the Resource CD.
Understanding the Status Bar (continued)
Then join the pieces of the fastener to attach the USB adapter in the plastic cradle to
the monitor.
Technical Support
After completing the Smart Wizard configuration assistant, locate the serial number on the
bottom label of your product, and use it to register your product at
http://www.NETGEAR.com/register.
Registration on the website or over the phone is required before you can use our telephone
support service. The phone numbers for worldwide regional customer support centers are
on the Warranty and Support Information card that came with your product.
Go to http://www.netgear.com/support for product updates and Web support.
Attention: When you configure the wireless settings of this device,
please make sure to select the correct country settings. Due to EU
law, the country settings must be identical to the country where the
device is operating.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear WN111v2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear WN111v2 in the language / languages: English as an attachment in your email.

The manual is 0,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info