519681
2
Zoom out
Zoom in
Previous page
1/2
Next page
December 2010
© 2010 by NETGEAR, Inc. All rights reserved. NETGEAR and the NETGEAR logo are registered trademarks of
NETGEAR, Inc. in the United States and/or other countries. Other brand and product names are trademarks or
registered trademarks of their respective holders. Information is subject to change without notice
.
Troubleshooting Tips
Here are some tips for correcting simple problems you may have.
No lights are lit on the wireless access point.
The wireless access point has no power:
Make sure the power cord is connected to the access point and plugged in to a
working power outlet or power strip.
Make sure you are using the correct NETGEAR power adapter supplied with your
access point.
The Ethernet light is not lit.
There is a hardware connection problem:
Make sure the cable connectors are securely plugged in at the access point and
the network device (hub, switch, or router).
Make sure the connected device is turned on.
The WLAN light does not blink during wireless
activity.
The wireless access point’s antennas are not working:
If the WLAN activity light remains off while the WG102-500 is transmitting or
receiving data, disconnect the adapter from its power source and then plug it in
again.
Make sure the antennas are tightly connected to the WG102-500.
Contact NETGEAR if the WLAN activity light remains off while the WG102-500 is
transmitting or receiving data.
You cannot configure the wireless access point from a browser.
Check these items:
The WG102-500 is properly installed, LAN connections are OK, and it is
powered on. Check that the LAN port LED is green to verify that the Ethernet
connection is OK.
If your computer uses a fixed (static) IP address, ensure that it is using an IP
address in the range of the WG102-500. The WG102-500 default IP address is
192.168.0.229 and the default subnet mask is 255.255.255.0. The WG102-
500 default setting is for a static IP address.
If the network where you are connecting it is using DHCP, configure it
accordingly. See the Reference Manual for the ProSafe® 802.11g Wireless
Access Point for more details.
You cannot access the Internet or the LAN with a
wireless-capable computer.
There is a configuration problem. Check these items:
You may not have restarted the computer with the wireless adapter to have TCP/
IP changes take effect. Restart the computer.
The computer with the wireless adapter may not have the correct TCP/IP settings
to communicate with the network. Restart the computer and check that TCP/IP is
set up properly for that network. The usual setting for Windows on the Network
Properties is set to “Obtain an IP address automatically.”
The WG102-500’s default values may not work with your network. Check the
WG102-500 default configuration against the configuration of other devices in
your network.
For full instructions on changing the access point’s default values, see the
Reference Manual for the ProSafe® 802.11g Wireless Access Point.
Technical Support
Thank you for selecting NETGEAR products.
After completing the Smart Wizard configuration assistant, locate the serial number on
the bottom label of your product, and use it to register your product at
http://www.NETGEAR.com/register.
Registration is required before you can use our telephone support service. Registration
via our website is strongly recommended.
Go to http://www.netgear.com.cn/support/index.asp for product updates and Web
support.
GPL may be added in this product. You can see the GPL license agreement at:
ftp://downloads.netgear.com/files/GPLnotice.pdf
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear WG102-500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear WG102-500 in the language / languages: English as an attachment in your email.

The manual is 0,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Netgear WG102-500

Netgear WG102-500 User Manual - English - 134 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info