519678
2
Zoom out
Zoom in
Previous page
1/2
Next page
May 2006
©2006 by NETGEAR, Inc. All rights reserved.
NETGEAR and the NETGEAR logo are registered trademarks of NETGEAR, Inc., in the United States and/or
other countries. Other brand and product names are trademarks or registered trademarks of their respective hold-
ers. Information is subject to change without notice.
Troubleshooting Tips
Here are some tips for correcting simple problems you may have.
No lights are lit on the access point.
The access point has no power.
Make sure the power cord is connected to the access point and plugged in to a
working power outlet or power strip.
Make sure you are using the correct NETGEAR power adapter
supplied with your access point.
The Ethernet light is not lit.
There is a hardware connection problem.
Make sure the cable connectors are securely plugged in at the access point and the
network device (hub, switch, or router).
Make sure the connected device is turned on.
The WLAN lights are not lit.
The access point’s antennas are not working.
If either of the Wireless LAN activity lights stays off, disconnect the adapter from its
power source and then plug it in again.
Make sure the antennas are tightly connected to the WAG302.
Contact NETGEAR if the Wireless LAN lights remain off.
I cannot configure the access point from a browser.
Check these items:
The WAG302 is properly installed, LAN connections are OK, and it is powered on.
Check that the LAN port LED is green to verify that the Ethernet connection is OK.
If you are using the NetBIOS name of the WAG302 to connect, ensure that your PC
and the WAG302 are on the same network segment or that there is a WINS server on
your network.
If your PC uses a Fixed (Static) IP address, ensure that it is using an IP Address in the
range of the WAG302. The WAG302 default IP Address is 192.168.0.230 and the
default Subnet Mask is 255.255.255.0. The WAG302 default setting is for a static IP
address. If the network where you are connecting it is using DHCP, configure it
accordingly. See the Reference Manual on the Resource CD for ProSafe Wireless
Access Point for more details.
I cannot access the Internet or the LAN with a wireless capable
computer.
There is a configuration problem. Check these items:
You may not have restarted the computer with the wireless adapter to have TCP/IP
changes take effect. Restart the computer.
The computer with the wireless adapter may not have the correct TCP/IP settings to
communicate with the network. Restart the computer and check that TCP/IP is set up
properly for that network. The usual setting for Windows on the Network Properties
is set to “Obtain an IP address automatically.”
The access point’s default values may not work with your network. Check the access
point default configuration against the configuration of other devices in your network.
For full instructions on changing the access point’s default values,
see the Reference Manual on the Resource CD for ProSafe Wireless Access Point.
Technical Support
Thank you for selecting NETGEAR products.
To register your product, go to: http://www.netgear.com/register
Go to http://www.netgear.com/support for support information.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear WAG302 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear WAG302 in the language / languages: English as an attachment in your email.

The manual is 0,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Netgear WAG302

Netgear WAG302 User Manual - English - 108 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info