602923

NAD VISO TWO Manual

30
Zoom out
Zoom in
Previous page
1/34
Next page
EXECUTING MACROS
To execute a macro, press and release [MACRO]; its key illumination lights
for 5 seconds. While it remains lit, press an HTR 6 key to which a macro has
previously been stored.
The corresponding macro will run; as each step executes, its “parent” Device
Selector’s key ashes lights briey; when execution is nished, the [MACRO]
key illumination goes out. Pressing any other HTR 6 key while a macro is
executing will abort the macro. Remember that you must hold the HTR 6 so
that its infrared emitter can activate the target components.
NOTE
Whenamacroexecutes,a1seconddelayisautomaticallyinserted
between its commands. If you need more than a 1 second delay between
particularcommands—forexample,topermitacomponenttopowerup
completely—youcanrecord“empty”stepsintothemacrobychanging
DeviceSelector“pages”withoutenteringactualcommandfunctions.
BUTTON ILLUMINATION TIMEOUT
The HTR 6’s key-illumination can be set to remain lit for 0-9 seconds. The
default value is 2 seconds. To set the illumination timeout, simultaneously
press-and-hold for 3 seconds both the HTR 6’s [DISP] and the [0-9] key, with
the digit corresponding to the desired timeout duration; the Learn LED will
ash twice to conrm the new setting. When set to zero, the illumination
will not turn on at all.
NOTE
KeyilluminationisthebiggestdrainontheHTR6’sbatteries.Ashort
key-illuminationtimeoutwillextendbatterylifeappreciably;turningit
oaltogether(setitto0seconds)willlengthenitstillfurther.
FACTORY RESET
The HTR 6 can be reset to its factory state, deleting all learned commands,
copied and punched-through keys, macros, and other setup information,
reverting all keys to their pre-programmed library commands.
To perform a factory reset simultaneously press-and-hold for 10 seconds
the HTR 6’s [ON] and [RTN] keys; the Learn LED will start to ash green.
Release [ON] and [RTN] before the second ash is complete; the Learn LED
will turn red, indicating the remote has been reset.
NOTE
Youmustrelease[ON]and[RTN]beforethesecondashgoesout,otherwise
theunitwillnotreset;shouldthisoccur,repeatthefullprocedure.
DELETE MODE
The HTR 6 can store learned, copied, and “default library” commands on any
single key (The default library commands are the pre-programmed NAD
codes, such as the native VISO TWO commands on the [AMP] “page.”).
You can delete commands by layers back “down” to the default library
command on any key, removing learned commands, punched-through
functions, and copied keys.
NOTE
The default library commands cannot be deleted, so you need not worry
thatusingDeleteModemightcauseirreparablechanges.
To enter Delete Mode, simultaneously press-and-hold for 3 seconds both
the desired key’s Device Selector key and the [RTN] key, until the Learn LED
turns green. Press the function key whose command you wish to delete;
the Learn LED ashes; the number of times indicates which type of function
has become active - see the table below. Press the active Device Selector
key again to exit Delete Mode.
NOTE
Youmaydeletemultiplefunction-keycommandsonthesameDevice
Selector“page,”buttodeletefrommorethanoneDeviceSelectorpage
youmustexitDeleteModeandthenre-enteritontherequiredpage.
Flashes Command Type
1 Default Library Command
2 Copied Library Command
3 Learned Command
OPERATION
USING THE HTR 6 REMOTE CONTROL
30
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD VISO TWO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD VISO TWO in the language / languages: English as an attachment in your email.

The manual is 2,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD VISO TWO

NAD VISO TWO User Manual - German - 34 pages

NAD VISO TWO User Manual - Dutch - 34 pages

NAD VISO TWO User Manual - French - 36 pages

NAD VISO TWO User Manual - Italian - 34 pages

NAD VISO TWO User Manual - Swedish - 34 pages

NAD VISO TWO User Manual - Spanish - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info