581069
1
Zoom out
Zoom in
Previous page
1/2
Next page
Low noise, wide band MC/MM phono stage
Connect your turntable to most ampliers and receivers
External 23.5V DC power supply
Gold plated input sockets
LED power indicator
High quality components
SETUP
A CONNECT TURNTABLE TO PP 2e
1 Ensure all ancillary equipment is turned o and the NAD PP 2e not yet
connected to its dedicated power Supply.
2 Connect the leads from the turntable to the appropriate input sockets
on the back of the NAD PP 2e - MC for moving coil, MM for moving
magnet cartridge. Make sure you connect the Right channel to the
Right input; the Left channel to the Left input. Normally, red connector
denotes the Right Channel; white denotes the Left channel.
3 Once the turntable leads are connected, set the MC/MM switch on the
back of the NAD PP 2e to the correct input setting.
B CONNECT PP 2e TO AN AMPLIFIER OR RECEIVER
1 Connect suitable RCA leads from the NAD PP 2e to the amplier or
receiver. Always use a so-called “Line-Level” input such as CD, AUX or
DISC. Never connect the lead from the NAD PP 2e to an input marked
PHONO or turntable.
2 Again, make sure to connect the red plug to the Right channel, and the
white plug to the Left channel of the amplier or receiver.
3 If the lead from your turntable is equipped with a separate earth (GND)
lead, connect this directly to a ground connection on the NAD PP 2e.
Use the thumb screw terminal “GND” which provides the grounding.
C CONNECT THE POWER SUPPLY TO THE PP 2e
1 Connect the dedicated Plug-in Power Supply to the NAD PP 2e
(marked23.5V).
2 Insert the Plug-in Power Supply to a live mains socket; the blue LED on
the NAD PP 2e’s front panel will light up. Installation is now complete.
As the power consumption of the NAD PP 2e is negligible, it can always be
left switched on. It is recommended however that you disconnect the Plug-
in Power Supply from the mains if you are not going to use the NAD PP 2e
for a prolonged period of time (such as a holiday).
D OPERATION
1 With setup completed and the NAD PP 2e plugged in to a live mains
socket, power up the turntable and the amplier or receiver the NAD
PP2e was connected.
2 Ensure that the amplier or receiver is set to the source or input where
the NAD PP 2e is connected and start playback of a vinyl record in the
turntable.
3 Adjust the volume level of the amplier or receiver accordingly.
®
PHONO PREAMPLIFIER PP 2e
User Guide
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD PP-2e at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD PP-2e in the language / languages: English as an attachment in your email.

The manual is 1,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info