745052
7
Zoom out
Zoom in
Previous page
1/10
Next page
ENGLISH
7
10 +12V TRIGGER IN/OUT
+12V TRIGGER OUT
The +12V TRIGGER OUT is used for controlling external equipment
equipped with a +12V trigger input.
Connect this +12V TRIGGER OUT to the other equipments
corresponding +12V DC input jack using a mono cable with 3.5mm
male plug.
This output will be 12V when the C 298 is ON and 0V when it is
either OFF or in standby mode.
+12V TRIGGER IN
With this input triggered by a 12V DC supply, the C 298 can be
switched ON remotely from standby mode by compatible devices
such as ampliers, preampliers, receivers, etc. If the 12V DC supply
is cut o, the C 298 will return to standby mode.
Connect this +12V Trigger input to the remote device’s
corresponding +12V DC output jack using a mono cable with
3.5mm male plug. The controlling device must be equipped with a
+12V trigger output to use this feature.
11 BRIDGE MODE
The C 298 amplier can be congured to be MONO (Bridge Mode),
more than doubling its output power. This way, the C 298 can be used
as part of a high power stereo or home-theatre system, by connecting
additional power ampliers.
In BRIDGED MODE (switch at ON (MONO) setting), the C 298 will
produce approximately 620W into an 8 ohm loudspeaker. In this mode,
the amplier sections will react as though the speaker impedance
has been halved. Low impedance speakers (under 8 ohms) are not
recommended when using Bridge Mode as these may cause the
ampliers thermal cut-out to operate if played at high levels.
Set BRIDGE MODE switch to the “ON (MONO)” position and connect
the speaker to the terminals marked “L +” and “R-” ensuring that the
“L+” is connected to the “+” terminal of your speaker and the “R-” is
connected to the speakers “ - ” terminal.
Set BRIDGE MODE switch to OFF (Stereo) for normal operation.
IMPORTANT NOTE
If C 368 is the signal source, connect only C 368 Right channel PRE OUT
to C 298 LEFT input (both C 368 and C 298 in BRIDGE mode). Never use
C368 Left channel PRE OUT to drive C 298 LEFT input.
12 SPEAKERS
Connect C 298’s Right speaker terminals marked “R +” and “R-” to
the corresponding “+” and “-“ terminals of your designated right
speaker. Repeat the same for C 298’s Left speaker terminals and
corresponding left speaker.
Double check the speaker connections before powering up the C 298.
IMPORTANT NOTES
The blue terminals must never be connected to ground (earth).
Never connect the blue terminals together or to any common ground
device.
Do not connect the output of this amplier to any headphone adapter,
speaker switch or any device that uses common ground for left and
right channels.
NOTES
Use 16 gauge (American Wire Gauge or AWG) or lower stranded wire.
Connections to the C 298 can be made with banana-type plugs.
Bare wire or pins can also be used by loosening the terminal’s plastic
nut, making a clean, neat connection and re-tightening. To minimize
the danger of a short circuit, ensure that only 1/2-inch of exposed wire
or pin is used to connect and no loose strands of speaker wire.
13 POWER
Supplies the AC mains power to the C 298.
When the POWER switch is set to ON position, the C 298 goes to
standby mode as shown by the amber status condition of the front
panel Power indicator.
Press the front panel Standby button to switch ON the C 298 from
standby mode.
If you do not intend to use the C 298 for long periods of time (such
as when on vacation), switch o the POWER switch.
With POWER switched o, the front panel Standby button cannot
activate the C 298.
14 FUSE HOLDER
Only qualied NAD service technicians can have access to this fuse
holder. Opening this fuse holder may cause damage thus voiding
the warranty of your C 298.
15 AC MAINS INPUT
The C 298 comes supplied with two separate mains power cords.
Select the mains power cord appropriate for your region.
Before connecting the plug to the mains power source, ensure that
it is rmly connected to the C 298’s AC Mains input socket.
Always disconnect the mains power plug from the mains power
source before disconnecting the cable from the C 298’s AC Mains input
socket.
IDENTIFICATION OF CONTROLS
REAR PANEL
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD C298 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD C298 in the language / languages: English as an attachment in your email.

The manual is 0,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD C298

NAD C298 User Manual - German - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info