745052
6
Zoom out
Zoom in
Previous page
1/10
Next page
ENGLISH
6
1 BALANCED
Connect XLR audio source to these connectors. Ensure that proper
pin congurations are followed – Pin 1: Ground, Pin 2: Positive
(signal live) and Pin 3: Negative (signal return).
2 SELECT
Use SELECT switch to choose which audio input will be the active
source.
Select SINGLE-ENDED audio input by setting SELECT switch to the
right towards the direction of SINGLE ENDED input.
Select BALANCED audio input by setting SELECT switch to the left
towards the direction of BALANCED input.
3 SINGLE-ENDED
Use a twin RCA-to-RCA lead to connect these sockets to the
left and right analog output of a preamplier, processor or any
compatible device.
4 GROUND
Ensure that the C 298 is plugged-in to a grounded AC wall outlet.
If a separate earth ground is necessary, use this terminal to ground
your C 298. The C 298 can be connected to ground by connecting
a ground lead wire or similar to this terminal. After insertion, tighten
the terminal to secure the lead.
5 LINE OUT
The LINE OUT sockets allow daisy-chaining” - use more than one
amplier to add speakers to the same channel.
Use dual RCA cable to connect LINE OUT to the corresponding
analog audio input of compatible devices such as ampliers,
receivers or other applicable devices.
6 INPUT SELECT
Use INPUT SELECT switch to manage audio output level.
• FIX: Audio output level is xed. The C 298 becomes like a basic
amplier with audio output level controlled by an external device.
• VAR: Audio output level can be adjusted using the INPUT LEVEL
control knob.
7 INPUT LEVEL
With INPUT SELECT switch set to VAR, the INPUT LEVEL control knob
can be used to adjust the audio output level of the C 298.
Turn clockwise to increase audio output level; counter clockwise to
lower it.
NOTE
The INPUT LEVEL is a level trim only and not a full volume control.
8 AUTO SENSE LEVEL
Auto Sense feature instantaneously turn the C 298 to operating mode
from standby mode if it senses a specic input signal level applied to
either the BALANCED or SINGLE-ENDED sockets. There are three Auto
Sense levels
SETTING INPUT LEVEL
Low 0.85 mV
Mid 1.7 mV
High 3.7 mV
Auto Sense mode can be enabled or disabled by the following steps.
Enable Auto Sense mode
At operating mode, press and hold front panel Standby button and
then release within 10-15 seconds. The Bridge mode indicator light
ashes three times.
Disable Auto Sense mode
At operating mode, press and hold front panel Standby button and
then release within 10-15 seconds. The Bridge mode indicator light
ashes two times.
9 SERVICE
Use for servicing purposes only. Not for consumer use.
IDENTIFICATION OF CONTROLS
REAR PANEL
© NAD C 298
2 3 5 6 7 8 9 10
1 4 13
12 14 1511
ATTENTION!
Please make sure that the C 298 is powered o or unplugged from the mains power source before making any connections. It is also advisable to power
down or unplug all associated components while making or breaking any signal or AC power connections.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD C298 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD C298 in the language / languages: English as an attachment in your email.

The manual is 0,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD C298

NAD C298 User Manual - German - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info