30282
54
Zoom out
Zoom in
Previous page
1/58
Next page
ROYAL evo
Seite 54
18.6. Sub-menu „New model“
When you open this sub-menu the following display
appears:
The transmitter tells you which memory number will
be used: it is always the first vacant memory. You can-
not change the memory number.
The template determines which basic settings are ac-
cepted into the memory (Î 12.4.). You can change this
setting if you wish.
Servo conf. (Servo configuration) defines the assign-
ment of the servos and the signal format. The following
combinations are possible:
Servo conf..
Servo
assignment
Signal format
MPX-MPX
MPX MPX
MPX-UNI
MPX UNI
Futaba
Futaba UNI
JR
JR UNI
The brand-specific assignment sequence (order of ser-
vos at the receiver output) is prepared in four servo
configurations. For MULTIPLEX e.g.: Throttle is on servo
4 and Rudder on servo 3. If the model was operated
with a radio of a different brand before, using the corre-
sponding configuration eases the assignment proce-
dure. In the menu K, Assignment the preset sequence
can be modified to your liking.
Mode defines the assignment of the sticks. In our ex-
ample the left-hand stick controls rudder and elevator.
You can change this setting if you wish.
Assignment defines which of the possible assignment
lists for transmitter controls and switches is to be used
with this model. You can change this setting if you wish.
Select OK to conclude the process, and the new model
is created.
Note:
If there are no vacant memories available, the screen
displays the number -1 and the note “No memory free!”
In this case press ENTER and then “EXIT” the menu.
19. Accessories
19.1. Scanner (with HFM-S RF module)
A scanner module can expand the Synthesizer RF mod-
ule HFM-S of the ROYALevo. The scanner can do two
„jobs“:
19.1.1. Scan the all frequencies/channels in
the band
All channels in the band will be measured sequentially.
Detected signals will show up in the display as bars. The
height of the bar corresponds to the strength of the
signal.
19.1.2. Channel-Check at power-ON
The channel selected for the synthesizer is checked
every time you switch your transmitter ON. If the chan-
nel is occupied already the synthesizer does not start
operation (no RF output) and in the display you will see
a warning. If no signal is detected on your channel,
normal operation starts.
19.1.3. Installation of the scanner module
The user can install the scanner. No tools or adjustments
are required.
Available frequencies/bands: see 19.3. Acessories
Detailed instructions are attached to the scanner mod-
ule.
19.2. Channel-Check
(with the RF module HFM-4)
A Channel-Check module can be installed in the RF
module HFM-4. This module needs a receiver crystal
with the same frequency/channel, which will be used
for the model.
Every time you switch your transmitter on, the module
checks if the channel is occupied or not.
The Channel-Check module for the ROYALevo
is identical with the module, used in the trans-
mitters PiCO line, COCKPIT MM and in the RF
module HFM3.
Available frequencies/bands: see MULTIPLEX
main catalogue
19.2.1. Installation of the Channel-
Check module
Switch OFF and open the transmitter
remove the RF module
Install the desired receiver crystal in the Channel-Check
module
plug Channel-Check module onto the RF module
reinstall the unit in the transmitter
19.2.2. Operating Channel-Check
Expand the aerial fully
Switch the transmitter on
LED glows permanently: Channel occupied
LED flashes: Channel free
(without guarantee)
If the channel is occupied the following message ap-
pears in the display:
Channel Used!
Channel-Check
module
54


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Multiplex ROYALevo9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex ROYALevo9 in the language / languages: English as an attachment in your email.

The manual is 3,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex ROYALevo9

Multiplex ROYALevo9 User Manual - German - 58 pages

Multiplex ROYALevo9 User Manual - Dutch - 110 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info