625666
14
Zoom out
Zoom in
Previous page
1/96
Next page
14
ENGLISH
ENG
can be used twice - turn if necessary.
Cutting blade
(as replacement), see
Accessories chapter.
Regrind worn cutting blade (10) if necessary
(see 12 Maintenance chapter)
7 Remove contamination, remains of leaves,
etc. (e.g. with a brush or cloth) Ensure that
the contact surfaces are particularly clean.
8
Mount cutting blade (10)
and rotate until it
engages on the drive spindle.
9
Block the cutting blade (10)
again to prevent
rotation (as described above).
10 Reinsert screw with Belleville spring (9) and
tighten clockwise with hexagon spanner
(8).
11 Remove wooden rod (or non-ferrous metal
rod).
12 Slide the enclosure (1) fully onto the cutting
blade.
13 Reinsert battery pack
(4)
.
8.4 Cleaning the cutting blades
(after every use)
Before cleaning:
Switch the machine off. Remove battery
pack (4) from machine.
Wear protective gloves.
Remove contamination, remains of blades etc.
(e.g. with a brush or cloth)
After cleaning:
Treat cutting blades with Metabo
machine care oil 6.30474 or Pump Spray 6.30475
(biologically degradable).
The maximum number of charge cycles can only
reached if an exhaustive discharge of the battery
pack is avoided. If performance diminishes,
recharge the battery pack.
9.1 Charging battery pack
Insert battery pack (4) up to stop in charging
compartment (13).
The operating display (15) flashes and the battery
is charged.
When the battery pack is fully charged, the oper-
ating display (15) lights up continuously.
The battery pack can remain in the battery charger
and is therefore always ready for use.
10.1 Warning display (14) lights up continu-
ously
Battery pack is not charged. Temperature too
high/too low. When the temperature of the
battery pack is between 0 °C and 50 °C, the
charging process begins automatically.
10.2 Warning display (14) flashes
Battery pack is defective. Remove the battery
pack immediately from the charger.
Short circuit between the charging contacts.
Check the contacts for foreign bodies.
Ensure that there are no birds brooding in your
hedge. If necessary, postpone your hedgecutting.
The chopped-up cuttings, combined with other
garden waste products, provide nutrient-rich
compost.
Unchopped cuttings placed in a natural garden
provide a useful place of retreat for small animals
such as hedgehogs.
Observe any local resting periods; your neighbour
will thank you for it.
Check that the screw and diaphragm spring
(9)
are seated securely
At regular intervals, check that the screw and
diaphragm spring (9) are seated securely using
an Allen key (8)
. The screw must always be
tight-
ened properly.
Fit a screw locking device to the
thread of the screw. The locking device will wear if
the screw is slackened and tightened frequently.
Replace the screw if necessary (order no.
341704440).
Blunt or damaged cutting blades (10)
Replace cutting blades (10) (or turn then over) if
they are blunt or damaged.
It is advisable to have blunt cutting blades (10)
sharpened in a specialist workshop. Check cutting
blades regularly for damage and have them
repaired in a specialist workshop immediately if
necessary.
9 Use of battery charger
10 Fault when charging
11 Tips and Tricks
12 Maintenance
17026903_0409 PowerCutter.book Seite 14 Dienstag, 14. April 2009 1:33 13
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo PowerCutter Li at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo PowerCutter Li in the language / languages: All languages as an attachment in your email.

The manual is 6,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info