625666
13
Zoom out
Zoom in
Previous page
1/96
Next page
ENGLISH
13
ENG
Pull out the mains plug immediately if the battery
charger starts to smoke or flames emerge!
See page 3 (please unfold).
PowerCutter...:
1Enclosure
2Handle
3 Battery pack release
4 Battery pack
5 Trigger switch
6 Switch lock (against accidental activation)
7 Hand protection
8 Hexagon spanner
9 Screw with Belleville spring (for securing
cutting blade)
10 Cutting blades
11 Upper cutting blade
12 Bearing
Battery charger LC 60:
13 C
harging compartment
14 W
arning display
15 O
peration display
Battery charger LC 60:
Automatic balancing of the individual battery
cells permits optimum utilisation of the available
capacity and, at the same time, lengthens the
service life of the battery pack.
PowerCutter...:
Check Quick stop:
Switch machine on briefly and then off again. Have
the machine repaired if braking time is clearly
lengthened.
Charge the battery pack before use (4).
Battery charger LC 60:
Before plugging in, check to see that the
rated mains voltage and mains frequency, as
specified on the rating label, match your power
supply.
Self-test
Insert the mains plug. The warning display (14) and
the operating display (15) light up in succession for
approx. 1 second.
8.1 Battery pack
Removing battery pack:
Press the battery pack release (3) and remove
the battery pack (4).
Inserting battery pack:
Push in battery pack (4) until it engages.
8.2 Switching On and Off
Switching on
(safety operation):
Push the switch lock (6) in the direction of the
arrow and press the trigger switch (5).
To switch off:
Release the actuated trigger switch (5).
Thanks to the patented Quick stop, the cutting
blades come to a standstill within approx. 0.3
seconds.
Have the machine repaired if braking time is
clearly lengthened.
The noise that sometimes occurs during a
machine Quick stop is design-related and has no
influence on operation and service life.
8.3 Replacing cutting blades
Replace cutting blades (10) (or turn then over) if
they are blunt or damaged.
Never check the sharpness of the cutting
blades with your fingers. The cutting blades
are blunt if the cut twigs or leaves are chapped or
frayed.
Remove the battery pack (4) from the
machine to prevent accidental activation.
Danger of injury from the sharp edges of the
blades. Do not touch the cutting blade (10)
and upper cutting blade (11). Wear protective
gloves.
See illustration (A), page 3.
1 Remove battery pack
(4)
.
2 Remove enclosure (1) from cutting blade.
3
Block the cutting blade (10)
with a sufficiently
long wooden rod (or non-ferrous metal rod)
to prevent rotation (do not block or hold
with your fingers or hand).
4 Remove screw with Belleville spring (9)
using a hexagon spanner (8) by turning
counterclockwise (right-hand thread).
5 Remove wooden rod (or non-ferrous metal
rod).
6
Carefully remove the cutting blade (10)
.
Cutting blades (10)
ground on both sides
5Overview
6 Special Product Features
7 Commissioning
8 Use of PowerCutter...
17026903_0409 PowerCutter.book Seite 13 Dienstag, 14. April 2009 1:33 13
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo PowerCutter Li at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo PowerCutter Li in the language / languages: All languages as an attachment in your email.

The manual is 6,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info