658520
21
Zoom out
Zoom in
Previous page
1/56
Next page
21
ENGLISH
Opening the upper/lower housing door:
1. Turn the turn-lock fastener anticlock-
wise approx. one turn.
The housing door opens slightly.
This activates the door interlock
which switches the motor off.
A
Danger from exposed bandsaw
blades and wheels!
If after one turn the motor does not
switch off or the door immediately
opens wide, the door interlock or the
closure system is defective. Shut
down the saw and return it to the Ser
-
vice Centre in your country for repair.
2. Turn the turn-lock fastener further
anticlockwise.
The housing door opens wide.
Closing the upper/lower housing door:
Press against the housing door and
turn the turn-lock fastener clockwise
until the housing door closes prop
-
erly.
Setting knob for band saw blade ten-
sion
With the setting knob (41) the band saw
blade tension is corrected, if necessary:
Turning the setting knob clockwise
increases the blade tension.
Turning the setting knob counter-
clockwise reduces the blade tension.
Quick release lever
With the quick release lever (42) the saw
blade tension is released.
Setting knob for blade tracking
adjustment
With the setting knob (43) the tilt of the
upper band saw wheel can be adjusted,
if necessary. This tracking adjustment is
required to have the blade run dead cen
-
tre on the rubber tyres of the band saw
wheels:
turning clockwise = blade moves to
the rear
Turning counter-clockwise = blade
moves to the front.
Speed adjustment
By shifting the drive belt the band saw
can be operated at two speeds (see
"Technical Specifications"):
370 m/min for hard wood, plastics
and non-ferrous metals (with special
band saw blade);
800 m/min for all kinds of wood.
A
Caution!
The drive belt must not run in a
diagonal position; this will damage
the belt
Setting knob for drive belt tension
With the setting knob (44) the drive belt
tension is corrected, if necessary:
turning the setting knob clockwise
reduces the blade tension;
turning the setting knob counter-
clockwise increases the blade ten-
sion.
Saw table tilt
After loosening the lock screw (45) the
saw table (46) tilts steplessly through 47°
against the blade.
Rip fence
The rip fence (47) clamps to the front of
the bandsaw table; in addition it is held in
position by the hold-down clamp (48) at
the rear of the bandsaw table. The rip
fence can be used on both sides of the
blade.
Mitre fence
The mitre fence (50) is inserted into the
table slot from the table’s front edge.
For mitre cuts the mitre fence turns to 60°
in both directions.
41
42
43
800 m/min370 m/min
44
45
46
47
48
49
50
51
21

Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo BAS 317 Precision at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo BAS 317 Precision in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 6,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Metabo BAS 317 Precision

Metabo BAS 317 Precision User Manual - Dutch, Portuguese, Spanish - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info