551340
17
Zoom out
Zoom in
Previous page
1/21
Next page
ENGLISH ENGLISH
12
13
InstallationInstallation
1. During the warm-up, the POWER LED will blink in blue until the signal link between the
TRANSMITTER and the RECEIVER is established. It will take 15 ~ 20 seconds for system
boot up successfully.
2. Ensure your TV set or projector is in “HDMI input” mode, and is already powered on.
3. Press the Source button on the RCU or on the top of receiver / transmitter for Source
input switch until you see the video being broadcasted from your device.
4. If all operation is normal, the POWER LED and INFO./CHANNEL LED will glow in solid
blue. Please refer to the below form containing detailed LED indicator and OSD de-
scription of transmitter / receiver:
Item / Mode
Status
Description
Power LED Status LED OSD Display
Standby
For power saving
mode.
Static Red Off
Initial Boot
up / Warm up
It will spend
15 ~ 20 seconds for
system boot up.
Blinking Blue Blinking
Searching
available
channels
Continuing search
available channels If
system can’t establish
link over 80s after
initialization.
Blinking Blue Blinking
Wireless
linked Mode
No input from
selected source
Static Blue
Blinking
(quickly)
Video format not
recognized
Static Blue
Blinking
(slowly)
Video format
is recognized
Static Blue Static Blue - - -
NOTE:
If the RF connection over 80sec and still not established, it might link lost or the trans-
mitter is most likely out of range. You may have to verify the range and adjust or shor-
ten the distance between your HDTV set with the transmitter and the receiver. The
maximum video transmission range for 1080p content is up to 66 feet in line of sight
(LOS). The minimum range should be 2 meters.
Please make sure the computer have been power on and switched the signal output
to HDMI out; also try to re-plug the HDMI cable to make sure the HDMI connector had
settled well.
If there is no video displayed and OSD displayed “Not Supported Format, this is an
indication that the video frame rate from the computer is not supported, please refer
chapter 5 to switch a supported video timing.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Megasat Wireless HD Sender Comfort at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Megasat Wireless HD Sender Comfort in the language / languages: English, German as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info