168723
14
Zoom out
Zoom in
Previous page
1/16
Next page
A M P L I F I E R S
ENG
TROUBLE SHOOTING
The key to finding the problem in a misbehaving sound system is to isolate
parts of that system in a logical fashion to track down the fault. Description
of the Diagnostic system built into all MB Quart amplifiers:
The diagnostic system will shut down the amplifier, until reset by turning the
head unit off, and back on. This state of affairs will be indicated by the front
panel PROTECT LED lighting up under the following conditions:
1 - A short circuit on the loudspeaker leads.
2 - An internal amplifier fault that causes a DC offset on the loudspeaker
output.
Should the amplifier go into diagnostic mode, simply disconnect all RCA and
speaker leads, while keeping +12 volt, power ground and remote leads connected.
1 - Now turn the amplifier back on, and if the diagnostic LED lights, the
amplifier has an internal fault.
2 - If not, plug the RCA cables back, and reset the amplifier. If it goes into
diagnostic now, the fault lies in the input, either with bad cables or source
unit.
3 - If the amplifier seems fine with RCA cables plugged in, connect the speakers,
one at a time, and if one of the speakers or its wiring is faulty, it will
activate the diagnostic system.
Amplifier heatsink overheating
The amplifiers will shut down when the heatsink temperature reaches 80° C,
and turn back on once the unit has cooled down below that point.
Causes of overheating:
1 - Inadequate cooling - relocate or remount to provide better natural airflow
over the fins.
2 - Driving high power levels into low impedances - back off on the volume
control, and/or make sure you are not loading the amplifier with less than
the recommended loudspeaker impedance.
Low output power
1 - Check that level controls have been set up properly.
2 - Make sure that the battery voltage, as measured at the amplifier’s +12 volt
and ground terminals, is 11 volts or more.
3 - Check all +12 volt and ground connections.
Fuses blowing
1 - The use of loudspeaker impedances below the recommended minimums
will draw more current - check.
2 - A short on the main +12 volt cable from the battery to the vehicle chassis
will cause the main fuse to blow.
3 - If an amplifier fuse blows continually, with only +12 volt, ground and
remote leads connected, the amplifier may be faulty.
System does not turn on
1 - Check all fuses.
2 - Check all connections.
3 - Measure the +12 volt and remote turn on voltages at the amplifier terminals.
If these are non existent or low, take voltage measurements at fuse holders,
distribution blocks, the head unit’s +12 volt and remote leads to localize
the problem.
Noise problems
System noise can be divided into two categories, hiss, and electrical interference.
Hiss, or white noise
1 - High levels of white noise usually occurs when amplifier level controls are
turned up too high - readjust according to the procedures in sectionSetting
up systems after installation for best performance”
2 - Another major problem that can cause excessive hiss, is a noisy head unit
- unplug the amplifier input RCA cables, and if the hiss level reduces, the
source unit is at fault.
Electrical interference
The inside of an automobile is a very hostile electrical environment. The
multitude of electrical systems, such as the ignition system, alternator, fuel
pumps, air conditioners, to mention just a few, create radiated electrical fields,
as well as noise on the +12 volt supply and ground. Remember to isolate the
problem - first unplug amplifier input RCA cables, if the noise is still present,
check the speaker leads, if not, plug the RCAs back, and investigate the source
driving the amplifier, one component at a time.
A ticking or whine that changes with engine RPM
1 - This problem could be caused by radiation pickup of RCA cables too near
to a fuel pump or a distributor, for instance, - relocate cables.
2 - Check that the head unit ground is connected straight to the vehicle chassis,
and does not use factory wiring for ground.
3 - Try to supply the head unit with a clean +12 volt supply directly from the
battery +, instead of using a supply from the in dash wiring/fusebox.
A constant whine
This type of noise can be more difficult to pinpoint, but is usually caused by
some kind of instability, causing oscillations in the system.
1 - Check all connections, especially for good grounds.
2 - Make sure that no speaker leads are shorting to exposed metal on the
vehicle chassis.
3 - RCA cables are notorious for their problematic nature, so check that these
are good, in particular the shield connections.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MB Quart dsc4125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MB Quart dsc4125 in the language / languages: English, German as an attachment in your email.

The manual is 6,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info