494280

Marmitek HomeGuard MS8000 Manual

4
Zoom out
Zoom in
Previous page
1/58
Next page
4 © MARMITEK
3. Siren:
Built-in 90dB(A) siren is triggered by an alarm and can be switched of (silent alarm) via the
keyboard after entering your personal access code (PIN).
4. Battery compartment:
Contains a back-up battery in case of a power failure or tampering. For longer back up times
a 9V alkaline (approx.10h) or Lithium battery (approx. 30h) can be used. Battery lifetime is
reduced each time the power is switched off or the power adapter is disconnected from mains.
If the HomeGuard is disconnected from mains for a longer period of time on purpose, remove
the battery first.
5. Status indicators:
red: • On continuously when the alarm is activated.
• flashes after the alarm has been triggered.
• is off when the alarm is de-activated.
green: • flashes when the device is being programmed.
• flashes when the device is being turned on (time delay).
• On continuously when the device is on.
6. Telephone input:
Connects the HomeGuard to the public telephone network with the supplied cable.
7. Power supply:
Only use the supplied 12V power adapter.
8. External alarm connector:
This input allows you to connect any external alarm device with a non-powered NO (Normally
Open) or NC (Normally Closed) connector. E.g. smoke alarms, magnetic door/window
connectors, flood and temperature detectors, etc. There may be multiple sensors connected
to the HomeGuard (serial for NC, parallel for NO alarm connectors). This allows you to turn
your HomeGuard into a complete security system with built-in telephone dialler. To connect
any external security device, use the supplied cable with mini-plug or install an equivalent jack
plug on these devices.
3. WIreLess KeY FoB remoTe CoNTroL Kr21e
1. ARM: Will put the HomeGuard into the armed position. The alarm is instant or delayed.
Delayed arming allows you to leave the room within 30 seconds or enter the room and
switch off the alarm within 15 seconds after entering. The factory default is instant arming
(no delay). To change this setting please refer to Delay Arm (8).
2. DISARM: Switches off and resets the HomeGuard.
3. PANIC: If pressed simultaneously will cause an alarm instantly.
4. Lights On/Lights Off: These buttons are not used with HomeGuard.
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek HomeGuard MS8000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek HomeGuard MS8000 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info