494334
5
Zoom out
Zoom in
Previous page
1/5
Next page
25
The junction box or distribution
box fitted with a Marmitek X-10
module must be covered with a
switching device or cover plate.
It must not be used without a
cover plate, see Figure 2.
Never cover Marmitek X-10
modules with insulation material
because this can restrict heat
dissipation.
The connecting wires of
Marmitek X-10 modules with
interface functionality are
potential-free. If the connecting
wires come into contact with
live components, this can lead to
irreparable damage to the
module. To prevent unconnected
wires from coming into contact
with live parts, these wires must
be insulated with insulating tape
or terminals.
PROG.
N
L
DAX
10
!
N
L
DAX
10
prog.
SAIX
Figure 2.
26
Instructions for installation & connection of modules
The Marmitek X-10 module may not be installed too close to
a heat source (such as a lamp, built-in spotlight or radiator).
The ambient temperature at the module may not be greater
than 35 °C.
Never use any instruments or force when installing the
Marmitek X-10 modules. The Marmitek X-10 modules contain
fragile electronics that can become defective or cause
malfunctioning as a result of an excessive mechanical load.
We recommend that the Marmitek X-10 modules be installed
against the rear wall of the junction box and that the
installation wiring be placed around the Marmitek X-10
module. If there are junctions in the junction box, you are
advised to place them in front of the Marmitek X-10 module.
PROG.
N
L
SAIX
P
!
27
When tightening the screws
of the Marmitek X-10
modules, the tightening
torque may not exceed 0.5
Nm. If the torque is higher,
the terminals may break off. If
one of the terminals breaks
off, the Marmitek X-10 module
may no longer be used.
Marmitek X-10 modules must
remain accessible at all times for
programming and maintenance
or service.
PROG.
N
L
DAX
10
M = max. 0.5 Nm
Max. torque for screw terminals
P
PROG.
N
L
DAIX
10
Industry standards
When applicable, the Marmitek X-10 modules and devices are compliant with the industry
standards written in directive 2002/95/EC (RoHS) and directive 2002/96/EC (WEEE directive
).
Copyrights
Marmitek is a trademark of Pattitude B.V., All rights reserved. Copyright and all other
proprietary rights in the content (including but not limited to model numbers, software,
audio, video, text and photographs) rests with Marmitek B.V. Any use of the Content,
but without limitation, distribution, reproduction, modification, display or transmission
without the prior written consent of Marmitek is strictly prohibited. All copyright and other
proprietary notices shall be retained on all reproductions.
20321 - 2010623
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marmitek AFX3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marmitek AFX3 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info