1. Press S1 button alternately to start and stop
the STOPWATCH.
2. Press S2 button to reset the STOPWATCH to
"0:00; 00."
START/STOP
RESET/ LAP
SECONDS
MINUTES
HOURS
S3
S3
S3
■
H O W T O S E T S E C O N D T I M E Z O N E
1. From NORMAL TIME mode, Press S3 button 2
times into DUAL TIME mode.
2. Press S4 button to begin setting procedure.
The HOURS digit starts flashing.
3. Press S1 button to set HOUR setting.
4. Press S3 button to move on to MINUTE setting.
* Selection of the digits to be adjusted is made
in the following order by pressing S3 button
and then pressing S1 button.
5.
Press S3 button after completing the setting.
■
H O W T O U S E E L B A C K L I G H T
Note:
1. The backlight of the watch employs an elec-
tro-luminescent (EL) light, which tends to lose
illuminating power after very long use.
2. The illumination provided by backlight may be
hard to see when viewed under direct sunlight.
* When the illuminating light becomes dim, re
-
place the batteries with new ones.
T h i s w a t c h c o n t a i n s p r e c i s e e l e c t r o n i c
components. Never attempt to open the case or
remove the back cover.
• BATTERY
CAUTION
Do not expose the old battery to fire
or recharge it. Keep it at a place be-
yond the reach of children. If a child
swallows it, consult a doctor immedi-
ately.
• WATER RESISTANT
Co n d it i o n
of u se
Ac c i de n t al
co n t ac t
wi t h wa t e r,
su c h a s
sp l a sh e s
an d ra in
Sw i m mi n g
an d ta k i ng
a s h owe r
Sk i n
di v i ng
Sc u b a
di v i ng
Indication
on the dial/
case back
No
In d i ca t i o n
* If your watch is 200 M/20 BAR, 100 M/10 BAR or
50 M/5 BAR water resistant, it is so indicated on
the dial/case back.
• Do not operate the buttons when the watch is
wet.
• If the watch is exposed to salt water, rinse it in
fresh water and then wipe it thoroughly dry.
• Should you find any water or condensation in
-
side the watch, immediately have it checked.
Water can corrode electric parts inside the
case.
NO NO NO
YE S YE S NO NO
YE S YE S NO
NO
NO
NO
YE S
WATE R R E -
SI S TA N T
WATE R R E -
SI S TA N T
(5 0 M /5 BA R
)
WATE R R E -
SI S TA N T
10 0M / 10 B AR
or a b ove
(
NO
(
Caution:
Leather straps are not water resistant except so
indicated, even if the watch head is water resist-
ant.
• ALLERGIC REACTION
Because the case and band touch the skin di-
rectly, it is important to clean them regularly. If
not, shirt sleeves may be stained and those with
delicate skin may develop a rash. Please wear
the watch with some play to avoid any possible
allergic reaction. If you develop a rash on your
wrist, stop wearing and consult a physician.
• MAGNETISM
Your watch will be adversely affected by strong
magnetism. Keep it away from close contact with
magnetic objects.
• SHOCKS AND VIBRATIONS
Your watch may be worn for normal sports activi-
ties, but be careful not to drop it or hit it on hard
surfaces.
• TEMPERATURE
Your watch is preadjusted so that constant accu-
racy may be insured at normal temperature.
• CLEANING
Use only a soft cloth and clean water for cleaning
your watch. Never use chemicals, as the water-
proof gasket will corrode.
P r i n t e d i n C h i n a
YE S
■
C A R E O F Y O U R L O R U S WATC H
S4
S3
PRESS S3
2 T I M E S
S3
DUAL TIME
HOUR SETTING BY
PRESSING S1
MINUTE SETTING BY
PRESSING S1
NORMAL TIME
S2
S1
S1
RELOAD
TIMER AND
SET
1. Press S1 button while in the TIMER mode to start
the COUNTDOWN TIMER.
2. The countdown signal “ :” appears and starts
flashing.
3. Press S1 button again to stop the COUNTDOWN
TIMER.
4. While in the COUNTDOWN TIMER MODE, press
S2 button to res et the count down t ime to
its starting value and to start to countdown
automatica lly or while in countd own t ime
mode press S2 button and then press S1 button
to reset the countdown time.
5. Press S3 button return to NORMAL TIME display.
Countdown Timer Operation
STOP
START
START
COUNTING STOP
S4
S3
S2
S1
*
Press S2 button in any mode to turn the illuminating
light on.
■
S E R V I C E
When your LORUS watch requires repair or servic-
ing, please see the enclosed WARRANTY/GUAR-
ANTEE.
S2
STOPWATCH
MODE
STOPWATCH
SIGNAL
LIGHT ON
TIMER
MODE
S1
S2
TIME
COUNTDOWN
SIGNAL
* Press S3 button return to NORMAL TIME display.
