Power adapterExternal power supply adapter (230 V); NEST 12 V / 2 A DC/S; barrel / bayonet (EU),
LANCOM item no. 111303
This product contains separate open-source software components which are subject to their own licenses, in particular
the General Public License (GPL). The license information for the device rmware (LCOS) is available on the device‘s
WEBcong interface under “Extras > License information“. If the respective license demands, the source les for the
corresponding software components will be made available on a download server upon request.
iVPN
OffVPN connection inactive
Green, permanentlyVPN connection active
Green, ashingVPN connecting
eISDN
OffInterface deactivated
Green, permanentlyD-channel active
Green, ickeringISDN data transfer
Red, ickeringISDN transfer error
Red / orange, blinkingISDN hardware error
bOnline
OffWAN connection inactive
Green, permanentlyWAN connection active
Red, permanentlyWAN connection error
cDSL
OffInterface deactivated
Green, permanentlyDSL connection active
Green, ickeringDSL data transfer
Red, ickeringDSL transfer error
Red / orange, blinkingDSL hardware error
Orange, blinkingDSL training
Orange, permanentlyDSL sync
Green, blinkingDSL connecting
dAnalog
OffInterface deactivated
Green, permanentlyInterface activated
Orange, blinkingIncoming call
Green, blinkingConnection active
hVoIP
OffNo SIP accounts dened or VCM is off
Green, permanentlyAll dened and active SIP accounts
(outgoing) were successfully registered
Red, permanentlyNot all dened and active SIP accounts
were registered (possibly still in process)
Red or green,
inverse ashing
Number of currently used lines (connecting
or connected)
fETH
OffNo networking device attached
Green, permanentlyConnection to network device operational,
no data trafc
Green, ickeringData transmission
gWLAN
OffNo Wi-Fi network dened or Wi-Fi module
deactivated. The Wi-Fi module is not
transmitting beacons.
Green, permanentlyAt least one Wi-Fi network is dened and
Wi-Fi module activated. The Wi-Fi module
is transmitting beacons.
Green, blinkingDFS scanning or other scan procedure
jReset
Reset buttonOperated e.g. with a paper clip
ashort press: Restart the device
along press: Reset the device
aPower
OffDevice switched off
Green, permanently*Device operational, resp. device paired /
claimed and LANCOM Management Cloud
(LMC) accessible
Red / green blinkingConguration password not set. Without a
conguration password, the conguration
data in the device is unprotected.
Red blinkingCharge or time limit reached
1x green inverse
blinking*
Connection to the LMC active, pairing OK,
device not claimed
2x green inverse
blinking*
Pairing error, resp. LMC activation code
not available
3x green inverse
blinking*
LMC not accessible, resp. communication
error
4
Please observe the following when setting up the device
A Do not rest any objects on top of the device
A For devices to be operated on the desktop, please attach the
adhesive rubber footpads
AIn case of wall mounting, use the drilling template as supplied
AKeep the ventilation slots on the side of the device clear
of obstruction
ARack installation with the optional LANCOM Rack Mount
(separately available)
LANCOM 1681V
Power
VDSL
Online
ETH 1
ETH 2
VPN
ETH 3
ETH 4
ISDN Status
a
VDSL interface
Use the supplied DSL cable for the IP-based line to connect the
VDSL interface and the provider’s telephone socket. For more
infor mation, please contact your Internet service provider.
b
Ethernet interfaces
Use the cable with the kiwi-colored connectors to connect one of
the interfaces ETH 1 to ETH 4 to your PC or a LAN switch.
c
Analog interfaces
Connect analog terminal devices to the analog interfaces either
directly via RJ11, or with the help of the enclosed TAE adapters,
either directly or via the additionally enclosed RJ11 twin adapters.
d
Conguration interface
Use a serial conguration cable to connect the serial interface
(COM) to the serial interface of the device you want to use for
conguring / monitoring (separately available).
e
ISDN interfaces
ISDN 1:
Internal (NT) or external (TE) ISDN bus.
This feature is controlled by LCOS.
ISDN 2:
Internal (NT) ISDN bus.
A 100-Ohm resistor for line termination is
switchable in LCOS.
f
USB interface
You can use the USB interface to connect a USB printer or a
USB memory stick.
g
Power
After connecting the cable to the device, turn the bayonet
connector 90° clockwise until it clicks into place.
Use only the supplied power adapter.
abcdef
g
Gigabit Ethernet 10/100/1000
ISDN 1ISDN 2
TE / NTNT
VDSL
Analog 1/3Analog 2/4
acebgfdihj
LANCOM R883+
Quick Reference Guide
Cloud-ready
*) The additional power LED statuses are displayed in 5-seconds
rotation if the device is congured to be managed by the LANCOM
Management Cloud.
Need help? Post your question in this forum.
Report abuse
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Lancom R883 plus at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Lancom R883 plus in the language / languages: English as an attachment in your email.
The manual is 0,53 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.