Accessories2 Ethernet cables 3 m (kiwi colored connectors); 1 serial conguration cable 1.5 m;
2 IEC power cords 230 V (not for WW devices);
1 set of mounting rails with accessories for xing the device in a 19“ rack; 1x 19“ bracket
MOUNTING AND CONNECTING THE DEVICE
*) The additional status LED statuses are displayed in 5-seconds
rotation if the device is congured to be managed by the LANCOM
Management Cloud.
LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks
of their owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for
technical errors and / or omissions. 111879/0120
LANCOM ISG-8000
Quick Reference Guide
Cloud-ready
a
Serial conguration interface
Use the included serial conguration cable to connect the serial
interface (COM) to the serial interface of the device you want to
use for conguring / monitoring.
b
USB interfaces
You can use the USB interfaces to connect USB printers or USB
storage devices.
c
Reset button
Pressed up to 5 seconds: device restart
Pressed longer than 5 seconds:
conguration reset and device restart
d
TP Ethernet interfaces
Connect the ETH 1 - ETH 8 TP Ethernet interfaces to your PC or a
LAN switch using one of the enclosed cables with the kiwi-colored
connectors.
e
SFP+ interfaces (10G / 1G)
Insert suitable SFP modules into the SFP ports ETH 9 - ETH 10.
Choose cables compatible with the SFP modules and connect
them as described in the module’s documentation.
SFP modules and cables are not included.
f
g
Power supply modules (device back side)
Supply power to the device via the power supply modules
connectors. Please use the IEC power cable supplied (separately
available for WW devices).
Removing the power supply modules
To remove a power supply module from the device move the
release lever to the right and pull out the modules using the
handle.
4
Please observe the following when setting up the device
AThe mains plug of the device must be freely accessible.
AFor devices to be operated on the desktop, please attach the adhesive rubber
footpads.
ADo not rest any objects on top of the device and do not stack multiple devices.
A Keep the ventilation slots on the side of the device clear of obstruction.
AMount the device into a 19” unit in a server cabinet using the provided screws and mounting rails.
dETH 1 - ETH 8 - TP (one green and orange LED each)
Both LEDs offNo networking device attached
Green, permanentlyConnection to network device operational,
no data trafc
Green, ickeringData transmission
Orange off1000 Mbps
Orange, permanently100 Mbps
aPower- / Status- / HDD LEDs
Power: offDevice switched off
Power: green,
permanently
Device operational
Statrus: green,
permanently*
Device operational, resp. device paired /
claimed and LANCOM Management Cloud
(LMC) accessible
Status: green / red,
blinking
No password set. Without a password
the conguration data in the device is
unprotected.
Status: red, blinkingCharge or time limit reached
Status: 1x green,
inverse blinking*
Connection to the LMC active, pairing OK,
device not claimed
Status: 2x green,
inverse blinking*
Pairing error, resp. LMC activation code
not available
Status: 3x green,
inverse blinking*
LMC not accessible, resp. communication
error
HDD: offno HDD read- / write access
HDD: green, ickeringHDD read- / write access
bLCD display (rotating in two lines)
ADevice name
AFirmware version
ADevice temperature
ADate and time
ACPU load
AMemory usage
ANumber of VPN tunnels)
AData transfer in reception direction
AData transfer in transmission direction
This product contains separate open-source software components which are subject to their own licenses, in particular
the General Public License (GPL). The license information for the device rmware (LCOS) is available on the device‘s
WEBcong interface under “Extras > License information“. If the respective license demands, the source les for the
corresponding software components will be made available on a download server upon request.
eETH 9 - ETH 10 - SFP+ (one orange LED each)
OffNo networking device attached
Orange, permanentlyConnection to network device operational,
no data transmission
Orange, ickeringData transmission
ISG-8000
ETH 9ETH 10
a
be
c
d
ISG-8000
ETH 9ETH 10
a
cde
ISG-8000
ETH 9ETH 10
b
cDisplay buttons A - D
All buttons are fully congurable
F
F
G
G
Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!
Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.
Detailed mounting instructions can be found under www.lancom-systems.com in the product area for this device under ‘downloads’.
Need help? Post your question in this forum.
Report abuse
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Lancom ISG-8000 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Lancom ISG-8000 in the language / languages: English as an attachment in your email.
The manual is 0,52 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
