Manual Laica NE1005 (page 24 of 24) (English, German, French, Italian, Portuguese, Spanish)

677510

Zoom out

Zoom in

1/24

Guidance and manufacturer’s declaration

electromagnetic immunity

The NEBULIZER MODEL NE1005 is intended for use in the electromagnetic environment

specified below. The customer or the user of the NEBULIZER MODEL NE1005 should assure

that it is used in such an environment.

Immunity test IEC 60601

test level

Compliance

level

Electromagnetic environment

-guidance

Conducted RF

IEC 61000-4-6

3 Vrms

150 kHz to 80 MHz

3 Vrms Portable and mobile RF communications

equipment should be used no closer to any

part of the NEBULIZER MODEL NE1005,

including cables, than the recommended

separation distance calculated from the

equation applicable to the frequency of

the transmitter.

Recommended separation distance

where P is the maximum output power

rating of the transmitter in watts (W)

according to the transmitter manufacturer

and d is the recommended separation.

Distance in metres (m). Field strengths

from fixed RF transmitters, as determined

by an electromagnetic site survey,a should

be less than the compliance level in each

frequency range. Interference may occur in

the vicinity of equipment marked with the

following symbol:

Radiated RF

IEC 61000-4-3

3 V/m

80 MHz to 2.5 GHz

3 V/m

NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.

NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by

absorption and reflection from structures, objects and people.

a. Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and

land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted

theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters,

an electromagnetic site survey should be considered. If the measured field strength in the location in

which the NEBULIZER MODEL NE1005 is used exceeds the applicable RF compliance level above, the

NEBULIZER MODEL NE1005 should be observed to verify normal operation. If abnormal performance

is observed, additional measures may be necessary, such as re-orienting or relocating the NEBULIZER

MODEL NE1005.

b. Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.

Guidance and manufacturer’s declaration

electromagnetic emissions

The NEBULIZER MODEL NE1005 is intended for use in the electromagnetic environment

specified below. The customer or the user of the NEBULIZER MODEL NE1005 should assure

that it is used in such an environment.

Emissions Compliance Electromagnetic environment-

guidance

RF emissions

CISPR 11

Group 1 The NEBULIZER MODEL NE1005

uses RF energy only for its

internal function. Therefore,

its RF emissions are very low

and are not likely to cause any

interference in nearby electronic

equipment.

RF emissions

CISPR 11

Class B The NEBULIZER MODEL

NE1005 is suitable for use in

all establishments, including

domestic establishments

and those directly connected to

the public low-voltage

power supply network that

supplies buildings used for

domestic purposes.

Harmonic emissions

IEC 61000-3-2

Class A

Voltage fluctuations/

flicker emissions

IEC 61000-3-3

Complies

Guidance and manufacturer’s declaration

electromagnetic immunity

The NEBULIZER MODEL NE1005 is intended for use in the electromagnetic environment

specified below. The customer or the user of the NEBULIZER MODEL NE1005 should assure

that it is used in such an environment.

Immunity test IEC 60601

test level

Compliance level Electromagnetic

environment

-guidance

Electrostatic

discharge (ESD)

IEC 61000-4-2

±6 kV contact

±8 kV air

±6 kV contact

±8 kV air

Floors should be wood,

concrete or ceramic tile.

If floors are covered with

synthetic material, the

relative humidity should

be at least 30 %.

Electrical fast

transient/burst

IEC 61000-4-4

±2 kV for power

supply lines and dc lines

±2 kV for power

supply lines and dc lines

Mains power quality

should be that of a

typical commercial or

hospital environment.

Surge

IEC 61000-4-5

±1 kV line(s) and neutral ±1 kV line(s) and neutral Mains power quality

should be that of a

typical commercial or

hospital environment.

Voltage dips, short

interruptions and voltage

variations

on power supply

input lines

IEC 61000-4-11

<5% UT

(>95% dip in UT)

for 0,5 cycle

40% UT

(60% dip in UT)

for 5 cycles

70% UT

(30% dip in UT)

for 25 cycles

<5% UT

(>95% dip in UT)

for 5s

<5% UT

(>95% dip in UT)

for 0,5 cycle

40% UT

(60% dip in UT)

for 5 cycles

70% UT

(30% dip in UT)

for 25 cycles)

<5% UT

(>95% dip in UT)

for 5s

Mains power quality

should be that of a

typical commercial or

hospital environment. If

a dips or an interruption

of mains power occurs,

the current of the

NEBULIZER MODEL

NE1005 may be dropped

off from normal level, it

may be necessary to use

uninterruptible power

supply or a battery.

Power frequency

(50/60 Hz)

magnetic field

IEC 61000-4-8

3 A/m 3A/m Power frequency

magnetic fields

should be at levels

characteristic of a typical

location in a typical

commercial or hospital

environment.

NOTE UT is the a.c. mains voltage prior to application of the test level

Recommended separation distances between

portable and mobile RF communications equipment and the NEBULIZER

MODEL NE1005

The NEBULIZER MODEL NE1005 is intended for use in an electromagnetic environment in which

radiated RF disturbances are controlled. The customer or the user of the NEBULIZER MODEL

NE1005 can help prevent electromagnetic interference by maintaining a minimum distance

between portable and mobile RF communications equipment (transmitters) and the NEBULIZER

MODELI NE1005 as recommended below, according to the maximum output power of the

communications equipment.

Rated maximum

output power

of transmitter

Separation distance according to frequency of transmitter

150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2.5 GHz

0.01 0.12 0.12 0.23

0.1 0.38 0.38 0.73

1 1.2 1.2 2.3

10 3.8 3.8 7.3

100 12 12 23

For transmitters rated at a maximum output power not listed above, the recommended separation distance d

in metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is

the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.

NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.

NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by

absorption and reflection from structures, objects and people.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Laica NE1005 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Laica NE1005 Manual

Product: