362235
10
Zoom out
Zoom in
Previous page
1/16
Next page
16
Press the button after having carried out all of these operations.
1 - Descaling cycle ± 8 mn
The
CALC
light stops blinking. The descaling cycle starts and is carried out automatically. The pump
occasionally sucks up water which comes out of the coffee nozzles and then the steam nozzle. This operation
lasts approximately 8 minutes.
When the cycle has completed, the ‘
’ and ‘
CALC
’ lights blink.
2 - First rinsing ± 6 mn
A rst rinsing is needed to eliminate the remaining scale remover. This cycle is run automatically. It lasts about
6 minutes.
Empty your receptacle full of waste water.
Empty the drip tray and then put it back again together with the receptacle as previously.
Empty, clean and rinse the water tank and then ll it again up to the “Max. level.
Replace your water tank. The ‘
CALC
’ light will ash and the ‘ ’ light will go off.
Press the
key. The ‘
CALC
’ light will become steady. The automatic cycle will last 6 minutes.
3 - Second rinsing
At the end of the rst rinsing, the ‘
CALC
’ light will ash. A second automatic cycle will last 6 minutes.
Remove your waste water recipient and the drip tray then t them again.
Again press the key. The ‘
CALC
’ light will become steady.
A second automatic cycle will last 6 minutes.
Once the second rinsing is nished, the ‘
CALC
’ light will go off.
Empty the drip tray and then t it again.
Empty and then ll your water tank.
Your appliance is now ready for use again.
Be sure to complete the entire scale removal cycle to avoid any risk of intoxication. The scale removal cycle
is a continuous cycle. Do not put your hands under the coffee outlets during the cycle.
Long rinsing program
When it is necessary to make a long rinsing program, the appliance warns you of this by ashing the
CLEAN
and
CALC
lights.
Remove, ll and replace the water tank.
Under the coffee outlets and steam nozzle place a recipient that can contain at least 0.15 L.
Launch the long rinse program by pressing on the button.
When the long rinsing program is complete, the ‘
CLEAN
’ and ‘
CALC
’ lights turn off.
TROUBLESHOOTING, CORRECTIVE ACTIONS
If one of the problems described in the table persists, contact KRUPS customer service.
If there is not enough water in the water tank, you will be warned by the ‘ ’ light.
Add the appropriate amount of water to the tank and scale removal will continue automatically.
If a power failure occurs during the cycle, you will have to start it up again from the start.
PROBLEM MALFUNCTION CORRECTIVE ACTION
Your machine detects a fault.
Switch off and disconnect the machine, remove the lter cartridge, wait for a
minute and restart the machine.
The appliance does not turn on
when the
button is pressed.
Check your fuses and plug sockets.
Check that the two power plugs are correctly pushed in the socket.
The coffee grinder makes a strange
noise.
There is a foreign body in the grinder. Disconnect the machine before investigating.
See if you can extract the foreign body using your vacuum cleaner.
The steam nozzle makes a noise. Check that the steam nozzle is correctly attached to its corresponding end piece.
10


Need help? Post your question in this forum.

Forumrules
1

Forum

krups-ea-8000

Reset search

  • EA8000 stuck on automatic maintenance and then gives error code 13. Any ideas what to try? Submitted on 17-7-2021 at 01:58

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Krups ea 8000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Krups ea 8000 in the language / languages: English as an attachment in your email.

The manual is 2,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Krups ea 8000

Krups ea 8000 User Manual - English - 12 pages

Krups ea 8000 Quick start guide - English - 26 pages

Krups ea 8000 User Manual - German - 12 pages

Krups ea 8000 Quick start guide - German - 26 pages

Krups ea 8000 User Manual - Dutch - 12 pages

Krups ea 8000 Additional guide - Dutch - 4 pages

Krups ea 8000 Quick start guide - Dutch - 26 pages

Krups ea 8000 User Manual - Dutch - 18 pages

Krups ea 8000 Quick start guide - Danish - 26 pages

Krups ea 8000 User Manual - French - 12 pages

Krups ea 8000 Quick start guide - French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info