570484

Konig Electronic CS500PLCNK100 Manual

5
Zoom out
Zoom in
Previous page
1/82
Next page
5
2.3 Removing HomePlug B from HomePlug A and C network and join HomePlug D and E
(Network BDE)
The procedure is as followes:
1. Press and hold the security button on HomePlug B for about 10 seconds. Release when the power
light flashes. The password to HomePlug B has just been erased and HomePlug B removes itself
from HomePlug A and C.
2. Press and hold the security button on HomePlug D for 2 seconds. The power light starts to flash.
3. Within 120 seconds after the power light on HomePlug D starts to flash, press and hold the security
button on HomePlug B for 2 seconds and then release.
4. HomePlug B and HomePlug D are now connected to each other. Therefore, together with
HomePlug E, they will form the network BDE.
Chapter 3: Troubleshooting & disclaimer
If your HomePlug AV Ethernet Bridge has difficulty communicating with each other, check the
following:
• Try power cycling the unit by unplugging it from the wall socket for 10 seconds and plug it in again.
• Hold the Reset button on each HomePlug for 15 seconds and try to re-connect. The HomePlug’s
light will flash, and the HomePlug will be reset and attempt to link using the default factory settings.
• Try plugging the HomePlug into an adjacent power outlet.
• The HomePlug works better when plugged directly into the wall power outlet. Connecting the
HomePlug to a power strip or surge protector may degrade the network performance or completely
stop network signals.
• This HomePlug should not be used in areas with excessive heat.
• Certain florescent or incandescent lights are noise sources for the electrical wiring and can
degrade the performance.
• If your building has more than one circuit breaker box, your HomePlug may not be able to connect
between the different circuit breaker boxes. In this case, connect one HomePlug to a power outlet
located on each of the circuit boxes. Connect an Ethernet cable between each of the HomePlug
units to link the different HomePlug together. This will allow the HomePlug units from different
circuit breaker boxes to be connected.
• To enter standby mode, simply remove the Ethernet cable from the HomePlug and wait about
3 minutes.
Remove HomePlug B from
Network ABC to Network DE
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Konig Electronic CS500PLCNK100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Konig Electronic CS500PLCNK100 in the language / languages: All languages as an attachment in your email.

The manual is 0,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info