570491

Konig Electronic CMP-BARSCAN21 Manual

2
Zoom out
Zoom in
Previous page
1/813
Next page
2
ENGLISH
Barcode scanner
Installing the USB interface scanner
To install the USB interface scanner the host device should have a USB port to receive data from the scanner.
Follow the steps as listed below:
1.) Make sure that the scanner has the right connector for the USB port of the host device.
2.) Connect the cable to the USB port of the device.
3.) If the LED indicator lights up and the buzzer sounds, the scanner is ready for use.
Configuration of the barcode scanner
Setup procedures
1.) Locate a group that contains the parameters to be changed.
2.) Scan the “Enter group #” label. The scanner will make a beeping sound to indicate that setup is in
progress.
3.) Scan the label representing the parameter to be changed.
4.) Scan the “Exit” to end the group currently selected, the scanner will beep.
5.) Repeat the procedure for the other groups, including the parameters to be changed.
Example 1:
Set the operating mode to “Continuous mode”.
1) Scan “Enter Group 5”.
2) Scan “Continuous/Trigger off".
3) Scan "Exit".
Example 2:
Assign the preamble string as "#", and postamble string as "END"
1) Scan "Enter Group 6"
2) Scan preamble
3) Refer to ASCII Table (page 50) and find the code number in hex decimal: # ASCII => 23 hex
The two digit numbers are: 2 3
4) Refer to Table-Hex: HEXADECIMAL (page 49) and scan the two digit labels accordingly.
5) Scan the “Confirm” label in Table-Hex
6) Scan “postamble”
7) Refer to the ASCII Table for the code numbers in hexadecimal (E => 45, N => 4E, D => 44)
8) Refer to Table-Hex: HEXADECIMAL (page 49) and scan the six digit labels consecutively.
4 5 4 E 4 4
9) Scan the “Confirm” Label in Table-Hex.
10) Go back to Group 6 and scan Exit.
Example 3:
Fixed Barcode Length Setting (i.e. Group 9-1 Interleaved 2 OF 5, Barcode Length= 15 digits):
1) Scan the Enter Group 9-1 Label
2) Scan the Length Define Label
3) Scan the Four Digit Labels in Table Hex (Page 49)
Tips:
• Refer to the Hexadecimal-Decimal Conversion Table (page 52) to get the barcode length in
Hexadecimal Number 15 dec => 0F hex
• The Four Digit numbers are: 0 F 0 F
• Refer to the Table-Hex: HEXADECIMAL (page 49) and scan the Four digit Labels accordingly.
4) Scan the Confirm Label in Table-Hex: HEXADECIMAL (Page 49)
5) Go back to Group 9-1 and scan the “Exit” Label.
Example 4:
3-Set Barcode Length Setting (i.e. Group 9-4: CHINA POSTAGE, the 3 Barcode Length Settings are as
below):
11 digits
28 digits
43 digits
2 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Konig Electronic CMP-BARSCAN21 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Konig Electronic CMP-BARSCAN21 in the language / languages: All languages as an attachment in your email.

The manual is 2,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info