166248

Kicker ix 404 impulse Manual

7
Zoom out
Zoom in
Previous page
1/8
Next page
7
Adjustments and Controls Setting Gain Control
The gain control is provided for level matching purposes. The control does not give
the amplifier any more power by turning it up. Its purpose is to adjust the sensitivity of
the amplifier in relation to the output level provided by the source.
Start with the amp gain set to minimum by turning the control counterclockwise. Turn
the source level up until distortion is barely audible. Then turn it down slightly. This will
typically be about 85% to 95% of full volume. Raise the amplifier gain until distortion is
just audible. The gain is now set correctly. Check the level with cd/tape and tuner to make
sure the adjustment is correct for all sources.
Setting KICKEQ™ Controls
The Bass and Treble controls on your Impulse Amplifier are provided to help tune your
system for ideal sound quality. After the system is installed and the vehicle is put back
together, do the listening test with music that is typical of the type you normally listen to.
Initially set the tone controls on the source unit to flat and turn the KICKEQ™ controls
fully counter-clockwise. Depending on your personal taste and the speakers used in the
system, you may want to increase the high or low frequencies by turning the KICKEQ™
controls clockwise. Remember that once the vehicle is in motion there will be apparent
loss of bass due to the masking effect of road noise. Do not attempt to make
adjustments while the vehicle is in motion. It is safer to pull off the road to
make changes.
Never change the crossover settings while the amplifier is on. A loud pop
will result which could destroy speakers or cause hearing loss.
SPECIFICATION
Model IX704 IX404 IX254
RMS Power (Watts/Channel) @12.5V, 4Ω Stereo 70 x 4 40 x 4 25 x 4
0.085% THD, All Channels Driven
RMS Power (Watts/Channel) @12.5V, 2Ω Stereo 105 x 4 60 x 4 35 x 4
0.2% THD, All Channels Driven
RMS Power (Watts/Channel) @12.5V, 210 x 2 120 x 2 65 x 2
4Ω Bridged Mono, 0.2% THD
Dynamic Power (Watts/Channel) @14.4V, 100 x 4 55 x 4 30 x 4
4Ω Stereo, 0.085% THD, All Channels Driven
Dynamic Power (Watts/Channel) @14.4V, 140 x 4 80 x 4 42 x 4
2Ω Stereo, 0.2% THD, All Channels Driven
Dynamic Power (Watts/Channel) @14.4V, 280 x 2 160 x 2 85 x 2
4Ω Bridged Mono, 0.2% THD
Dimensions (In., MM) 13.8, 350 11.4, 289 7.8, 198
(All Models 2.5”H x 9.5”W x ...”L,
63mmH x 241mmW x ...mmL)
Frequency Response 20Hz-20kHz ±0.5dB
Input Sensitivity High Level 1V-10V, Low Level 150mV-3.0V
Signal-to-noise Ratio >95dB, a-weighted, re: rated power
Active Electronic Crossover 18dB/ octave, selectable @70Hz or 110Hz;
KICKEQ™ Bass Boost Variable to +18dB, centered @ 40Hz
KICKEQ™ Treble Boost Variable to +12dB, centered @ 18kHz
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kicker ix 404 impulse at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kicker ix 404 impulse in the language / languages: English as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info