606707
77
Zoom out
Zoom in
Previous page
1/77
Next page
SKY CMD-3
CONTROL OPERATION
When in the Sky Command mode, the Microphone keys of
the Commander will function as below. First switch ON the HF
transceiver and press Microphone [0] on the Commander.
Each time you press the desired key, the Commander will
automatically enter transmit mode and send the corresponding
control command to the Transporter.
Key Function
[1] (PWR) Power ON/ OFF
[2] (RX) HF frequency receive ON/ OFF
[3] (MODE) Modulation mode switch
[4] (RIT)
RIT ON/ OFF
[5] (XIT)
XIT ON/ OFF
[6] (CLR)
RIT offset or XIT offset clear
[7] (SPLIT)
Split-frequency ON/ OFF
[8] (M>V)
Transfer from Memory to VFO
[9] (A/B)
In VFO mode: VFO A/ VFO B switch
In Memory Recall mode: no change
[0] (SYNC)
Current settings retrieve (from HF transceiver)
[A] (MONI)
To monitor the UHF band on the
Commander
[B] (M/V)
VFO/ Memory Recall mode switch
[C] (UP)
XIT/ RIT offset frequency increase
[D] (DOWN)
XIT/ RIT offset frequency decrease
[ ]
1
(FAST)
In LSB, USB, or CW mode: 10 Hz/ 1 kHz
switch
In FM or AM mode: 1 kHz/ 10 kHz switch
[#]
2
(ENTER)
In VFO mode: frequency entry ON
In Memory Recall mode: channel number
entry ON
[PTT]
To transmit audio on an HF frequency
1
“FS” appears when you select 1 kHz step (LSB/ USB/ CW) or 10 kHz step (FM/
AM).
2
After pressing Mic [#], press Mic [0] to [9] to enter a frequency or memory
channel number.
Note: To change the frequency or memory channel on the HF transceiver,
rotate the Tuning control.
PROGRAMMING CALLSIGNS
The built-in TNCs of the Commander and Transporter
communicate each other when you send a control command
from the Commander. So you must program different callsigns (9
digits max.) on these transceivers as the IDs of the TNCs.
Use the following Menu Nos. to program callsigns:
On Commander
700
COMMANDER
CALLSIGN
Callsign for Commander
701
TRANSPORTER
CALLSIGN
Callsign for Transporter
On Transporter
700
COMMANDER
CALLSIGN
Callsign for Commander
701
TRANSPORTER
CALLSIGN
Callsign for Transporter
1 Access Menu 700 or 701, then press the Tuning control.
The callsign entry fi eld appears; the fi rst digit blinks.
2 Rotate the Tuning control to select a character.
You can enter 0 to 9, A to Z, and –.
3 Press [].
The cursor moves to the next digit.
4 Repeat steps 2 and 3 to enter up to 9 digits.
[BACK]: Cancels entry of a callsign.
[]: Causes the cursor to move backward.
[INS]: Inserts the currently selected character.
[CLR]: Deletes the digit at which the cursor is blinking.
5 Press the Tuning control to complete the setting.
6 Press [ESC] to exit Menu mode.
The keypad on the Microphone also is available to enter
alphanumeric characters in step 2.
PROGRAMMING A TONE FREQUENCY
On receiving a tone from the Commander, the Transporter
causes the HF transceiver to enter Transmit mode. On both the
Commander and Transporter, access Menu 702 and select the
desired, same tone frequency.
77


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TM-D710GA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TM-D710GA in the language / languages: English as an attachment in your email.

The manual is 7,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TM-D710GA

Kenwood TM-D710GA User Manual - English - 55 pages

Kenwood TM-D710GA User Manual - German - 74 pages

Kenwood TM-D710GA User Manual - Dutch - 75 pages

Kenwood TM-D710GA User Manual - Dutch - 55 pages

Kenwood TM-D710GA User Manual - French - 77 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info