606707
76
Zoom out
Zoom in
Previous page
1/77
Next page
SKY CMD-2
PREPARATION FLOW
The following steps should guide you to a good start of Sky
Command operation. First connect the Transporter to the HF
transceiver.
1 <On the Commander and Transporter> Select the same VHF
and UHF frequencies.
Band A: VHF frequency Band B: UHF frequency
or
Band A: UHF frequency Band B: VHF frequency
Note: Confi gure the squelch to an appropriate level for both the VHF and
UHF band on the Commander and Transporter. If the squelch is not set to an
appropriate level, the transceivers may enter a BUSY state due to noise signals
and be unable to transmit.
2 <On the Commander> Access Menu 700 to program a
callsign (9 digits max.) for the Commander.
You may enter your exact callsign; ex. W6DJY.
3 <On the Commander> Access Menu 701 to program a
callsign (9 digits max.) for the Transporter.
This callsign must be different from the one for the Commander.
So you may add SSID characters; ex. W6DJY-1.
4 <On the Transporter> Access Menu 700 to program the same
callsign as you entered in step 2.
5 <On the Transporter> Access Menu 701 to program the same
callsign as you entered in step 3. The same callsign as you
entered in step 2.
6 <On the Commander and Transporter> Access Menu 702
and select the tone frequency.
Select the same tone frequency on both transceivers.
7 <On the Commander> Access Menu 703 and select
“COMMANDER”.
“Push [ 0 ] key to start Commander!!” appears.
8 <On the Transporter> Access Menu 703 and select
“TRANSPORTER”.
Now the Commander and Transporter are in Sky Command mode.
For operations in this mode, see “CONTROL OPERATION”. First
switch ON the HF transceiver and press [SYNC] on the Commander.
To exit the Sky Command mode, access Menu 703 and select “OFF”.
Note:
Unless you program callsigns, you cannot select “COMMANDER” or
“TRANSPORTER” using Menu 703.
On the HF transceiver, select 9600 bps and 1 stop bit (default) using the
Menu Set-up function.
Adjust the audio level on both the Transporter and HF transceiver while
listening to audio output from the Commander. An appropriate position of
the AF control on the HF transceiver might be in the range, 8:30 to 9:00.
To distinguish your various stations or nodes, you can have up to 15
Secondary Station IDentifi ers (SSIDs); ex. W6DJY-1 to W6DJY-15. You
always have to put a dash between your callsign and SSID number.
ATTENTION: Use only after verifying that there is no reception disruption
during communications.
76


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TM-D710GA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TM-D710GA in the language / languages: English as an attachment in your email.

The manual is 7,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TM-D710GA

Kenwood TM-D710GA User Manual - English - 55 pages

Kenwood TM-D710GA User Manual - German - 74 pages

Kenwood TM-D710GA User Manual - Dutch - 75 pages

Kenwood TM-D710GA User Manual - Dutch - 55 pages

Kenwood TM-D710GA User Manual - French - 77 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info