473137
16
Zoom out
Zoom in
Previous page
1/20
Next page
KTF-3010/KTF-2010 (En)
16
Do not use contact cleaners because it could cause a malfunction. Be specially careful against contact cleaners containing oil, for they may
deform the plastic components.
Note
Note
Operation to reset
The microcomputer may fall into malfunction (impossibility to
operate, erroneous display, etc.) when the power cord is unplugged
while power is ON or due to an external factor. In this case, ex-
ecute the following procedure to reset the microcomputer and
return it to normal condition.
Unplug the power cord from the power socket and, while
holding the ON/STANDBY key depressed, plug the power
cord into the socket again.
÷ Please note that resetting the microcomputer clears the contents
stored in it and returns it to the condition when it left the factory.
Symptom Cause Remedy
÷ Use audio cords to connect the tuner to the
amplifier.
4
÷ Connect an antenna. 5
÷ Set the broadcast band properly. 8
÷ Tune the frequency of the desired station.
8
÷ Set the ANT A/B key properly.
(KTF-3010 only).
7
÷ If located far from the broadcast station, in-
stall a dedicated FM outdoor antenna (5–6
elements).
÷ Preset the desired station.
0
÷ Preset the station again. 0
÷ Install the outdoor antenna away from the
road.
÷ Turn off the power of the appliance.
÷
Install the system further apart from the TV set.
÷
Install the system further apart from the PC.
÷ Set the IF BAND to WIDE. 7
÷ The tuner is not connected to the amplifier.
÷ No antenna is connected.
÷ The broadcast band is not set properly.
÷ The frequency of the desired station is not
tuned.
÷ The ANT A/B key is not set properly
(KTF-3010 only).
÷ The signal detected by the antenna is weak.
÷ No station is preset in the recalled channel.
÷ The preset memory was cleared because the
power cord had been unplugged for a long
period of time.
÷ Noise due to ignition noise of an automobile.
÷ Noise due to an influence from an electric
appliance.
÷ Noise due to a nearby TV set.
÷ There is a PC nearby.
÷ The broadcasted sound level is too high.
No sound is heard.
Radio stations cannot be received.
No station is received when a numeric key
pressed.
Interference.
Sound is distorted when the IF BAND is set
to NARROW (KTF-3010 only).
When the amplifier and the tuner are connected with the system control cord 4
Even if the input selector of the amplifier is connected to the source other than the tuner, the input selector of the amplifier switches to the
tuner when the desired program starts in the EON reservation mode.
Combined with the [SL16], the input selector returns to the original source after the desired program finishes, however, with a [XS8] it will not.
What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the table below to see if the
problem can be corrected before seeking help from your dealer or service representative.
In case of difficulty
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KTF 3010-2010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KTF 3010-2010 in the language / languages: English as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info