Manual Kemppi Robot Gun Cleaning Station (page 25 of 27) (English)

686375

Zoom out

Zoom in

1/27

Robot Gun Cleaning Station© Kemppi Oy 2016 1616

OPERATING MANUAL

14. TROUBLESHOOTING

If the measures described below are not successful, please consult your dealer or the manufacturer.

Also consult the operating instructions for the welding components: the welding power source, welding torch system,

re-circulating cooling unit, and so on.

Problem Cause Solution

Compressed-air motor does not run • Compressed-air supply or hose connection interrupted

• Compressed-air supply or hose connection interrupted

• Check all supply lines leading to the cylinder and the ttings

• Motor defective; replace

• Replace directional valve Y2

Insucient cleaning • Milling cutter defective or worn out • Replace milling cutter

Welding torch parts damaged • Wrong equipment parts • Check torch-dependent parts (milling cutter and clamping prism)

• Check immersion depth of torch

Table 12: Troubleshooting the injection unit

Problem Cause Solution

No injection • Insucient uid level

• Compressed-air supply or hose connections

interrupted

• Directional valve Y4 does not switch

• Add more anti-spatter uid

• Check all supply lines leading to the cylinder and the ttings

• Replace directional valve Y4

Too much or too little spray mist • Metering quantity incorrectly adjusted • Change setting of throttle screw

Too little spray mist • Injection time too short

• Operating pressure too low

• Injection time greater than waiting time

• Check operating pressure

No spray mist • Operating pressure too low • Check operating pressure

Table 13: Troubleshooting the wire-cutting device

Problem Cause Solution

No cutting function • Compressed-air supply or hose connection interrupted

• Directional valve Y3 does not switch

• Check all supply lines leading to the cylinder and the ttings

• Check signal output of robot control

• Replace directional valve Y3

Insucient cutting capacity • Too low working pressure

• Roughly running slide

• Worn cutting edge

• Check the adjustment of the pressure regulator: min. 5 bar, max. 8 bar

• Unmount movable parts; clean and lubricate them

• Clean more often

• Change approach position P4

• Change the cutter

Free wire end is bent • The wire has no contact with the xed jaws

• Counter-support jammed

• Correct the approach position of the welding torch

• Unmount movable parts; clean and oil them

• Tighten the mounting screws

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi Robot Gun Cleaning Station in the language / languages: English as an attachment in your email.

The manual is 2,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kemppi Robot Gun Cleaning Station Manual

Product: