28350

JRC JMA9933SA Manual

70
Zoom out
Zoom in
Previous page
1/404
Next page
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
2-10
2
C: CENTER Indicates that the EBL1 starting point is at the own ship position.
O: OFFSET Indicates that the EBL1 starting point is not at the own ship position.
In this state, the starting point may be at the cursor position or it may be fixed at an arbitrary
position on the screen. When the button is clicked, the starting point will move with the
cursor position, then when the left button is clicked the starting point will be fixed at the
cursor location.
L: After moving the L/L FIX EBL1 starting point, the starting point is fixed by the latitude and
longitude values.
If the starting point moves out of the screen, then it will be reset automatically so that the
starting point is at the own ship position.
Note: When the EBL1 starting point moves, the mode O or L is indicated by the position
selected among the EBL OFFSET ORIGIN menu.
EBL2 starting point mode
Sets whether the EBL2 starting point is placed at the center of the own ship or at an arbitrary
position on the radar screen.
Everything else is the same as that for the EBL2 starting point mode.
Speed unit setting
Sets the speed unit.
Clicking this button will open a pull-down menu. A unit can be selected from one of the
following. An alarm is activated if the selected speed unit is not connected to the radar.
Options: MANUAL, LOG (1-axis log), 2AXW (2-axis over water), 2AXG (2-axis over ground),
GPS
If the speed unit setting is “MANUAL,” then placing the cursor over the numeric section and left
clicking will allow numeric input.
SET/DRIFT
Turns on and off SET/DRIFT correction.
If CORRECTION is on for this setting, then “CORR” will be displayed next to the button. The
number displayed next to “CORR” at this time will be valid. Also, correction can only be set
when the speed unit is in the MANUAL or LOG (1-axis log) modes.
SET setting
Placing the cursor over the numeric section and left clicking will allow numeric input. This
setting is only valid if CORRECTION is ON.
DRIFT setting
Placing the cursor over the numeric section and left clicking will allow numeric input. This
setting is only valid if CORRECTION is ON.
Date display mode
Sets the date mode to be displayed on the screen.
: Turns off the time display.
: Global time display (UCT).
: Local time display (LOCAL).
ARPA, PAST POSN vector mode setting
These set the vector display mode.
T: True vector
R: Relative vector
These settings work concurrently.
40
41
42
43
39
U
L
… 70 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JRC JMA9933SA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JRC JMA9933SA in the language / languages: English as an attachment in your email.

The manual is 7,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info