626531
4
Zoom out
Zoom in
Previous page
1/4
Next page
enjoy motors ®
JE 50 RA 916 radio motor is a product from Jolly Motor España, s.l. www.enjoy-motors.com 4
JE50RA-916-STEEL_eng_ver. REM 2 & REM 2T
9-1 REPLACEMENT THE FIRST EMITTER (Main emitter) through the Switch Power Off/On
switch
OFF/ON
BIP
2
’’
seconds
2
minutes
4
enjoy
Switch power OFF, in the motor which we
want replace the MAIN transmitetr.
After 5 seconds, switch power ON
Between 2 seconds and 2 minutes (and
six seconds) after the power ON, the motor
willmakeasingletiltmovementasconr-
mation that it is ready to learn a new Main
On the new Main Emitter:
Press FOUR times the P3 button (located
on the back of the emitter)
Then the motor will make two tilt movement
asconrmationthatthenewMainemitter
has been learned
During the replacement process:
• Any order send by a transmitter will stopped the replacement process (even if the order is coming from a transmitter not learned with the motor. It is enought with the same
frequency).
When we replace the MAIN transmitter:
• Old main transmitters doesn’t work with the motor.
• Old transmitters copied on the motor, remain working on the motor
• The limit switches set up remain memorized on the motor.
9-2 REPLACEMENT THE FIRST EMITTER (Main emitter) through the Switch Power Off/On, if in the motor has not been seted up the limit switches
switch
OFF/ON
BIP
BIP
BIP
BIP
BIP
BIP
BIP
1
switch
OFF/ON
BIP
2
’’
seconds
2
minutes
4
Switch power OFF, in
the motor which we
want replace the MAIN
transmitter.
After 5 seconds, switch
power ON Motor will emit
till SEVEN BIPs
On the new Main Emitter:
Press ONE time the P3
button (located on the
back of the emitter)
Switch power OFF, in
the motor which we
want replace the MAIN
transmitter.
After 5 seconds, switch
power ON
Between 2 seconds and 2
minutes (and six seconds) after
the power ON, the motor will
make a single tilt movement as
conrmationthatitisreadyto
learn a new Main
On the new Main Emitter:
Press FOUR times the P3
button (located on the back
of the emitter)
Then the motor will make
two tilt movement as
conrmationthatthenew
Main emitter has been
learned
10 FULL RESET (DELETE ALL TRANSMITTTERS, LIMIT SWITCHES SET UP, ...) through any transmitter learned on the motor
switch
OFF/ON
hold
5
seconds
BIP
BIP
BIP
BIP
1 2 3 4 5 6 7 8
BIPBIPBIPBIP BIP BIP BIP BIP
10
BIP
9
BIP
Switch power OFF, in the
motor which we want do
the FULL RESET. After 5
seconds, switch power ON
Press TEN times the P3 button (located on the back of the emitter). Be sure to HOLD pressing on the TEN time.
Then the motor will make
two tilt movement as
ConrmationthataFULL
RESET has been done
NOTE:assoonasthemotorconrmthetotalcanecllation,themotorreturnstotheoriginalparameters.Willbenecessarystartfromthepointno.2tolearnaMaintransmitetrs.
WHAT TO DO IF?
1. Transmitter (learned on the motors) doesn’t work:
• The battery is consumed, replaced it by a new one.
• Be sure that motor is powered ON.
• Check if any interference in disturbing the signal.
2. Motor is working Step by Step (deadman):
• No limit switches are setted up on the motor. Set up them (up and down). After that motor will work in automatic mode.
3. Up and Down buttons are not in correspondende with the motor movement:
• If you have not set up the limit switch, do it, starting with the down limit switch.
• If limit switches have been setted up, you have to delete it (point 5) and set up agin (point 4-1 and 4-2).
4. Atter a power OFF/ON, the motor is emitting till SEVEN BIPs:
• Limit switches have been not setted up, please set up them (points 4-1 and 4-2).
5. Main transmitter doesn’t work or it is missing:
• Replace the Main transmitter, follwong the instructions (point 9-1 or 9-2).
6. Roller shutter is stopping in a wrong point:
• Do a full movement in ecah direction (up and down). After that check again. If motor still not stopping on the desires point, will be necessary delete its limit switch (point 5)
and does it again (point 4-1 and 4-2).
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jolly Motor JE50 RA9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jolly Motor JE50 RA9 in the language / languages: English as an attachment in your email.

The manual is 0,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info