701229
5
Zoom out
Zoom in
Previous page
1/8
Next page
C7-100ct: Installation
PROTECTION CAPACITOR
A high-quality 15μF protection capacitor is
included with the C7-100ct to guard against damage
from transient electrical pops (turn-on/off). This
capacitor is not a substitute for high-pass filtering
and must be connected in all installations. The
capacitors value has been selected so as not to
interfere with a properly set active high-pass filter.
The protection capacitor supplied with your
C7-100ct should be installed in a dry location and
as near as possible to the tweeter. Connect the
protection capacitor in-line (series) with the tweeter’s
positive (+) lead, as shown in Diagram A below. The
capacitor is bipolar and may be connected in either
direction. Make sure to insulate the capacitor’s leads
to guard from touching against any exposed metal.
Use plastic cable ties or a similar fastener to securely
mount the capacitor to avoid coming loose in the
event of a collision, sudden jolt or repeated vibrations
during normal use. Make sure that your mounting
location will not cause damage to wiring or any other
vital component of your vehicle.
TWEETER CONNECTIONS
Run the wire leads from the tweeter mounting
locations to the amplifier outputs. Then connect the
harness wire leads to the speaker/amplifier outputs
and tweeters, observing correct polarity. See
Diagram A below for details.
WARNING
!!
It is absolutely vital that the protection capacitor
is connected, as shown in Diagram A. Failure to
connect the protection capicitor as shown will result
in damage which is NOT covered under warranty.
TWEETER INSTALLATION
C7 tweeters have been designed for surface or
flush-mounting. Before choosing a method, carefully
inspect the desired mounting location to determine
which method will work best.
Surface-Mount: uses the supplied surface-
mount fixture and requires the drilling of three
holes (two for the wires and one for the mounting
screw). This application is useful when mounting the
tweeters to a panel that has insufficient clearance
behind it for the tweeter’s magnet structure.
Flush-Mount: yields a custom-installed
appearance and requires a 1.88-inch (48 mm)
diameter hole to be cut in the vehicle panel. At least
1.75-inch (44 mm) of clearance is required behind
the tweeter mounting surface for the spring clip and
1-inch machine screw used to mount the fixture.
In limited depth applications, it may be necessary
to cut down the length of the machine screw, or to
use a shorter screw (not supplied). Hand-tighten the
machine screw until the fixture is secure, as shown
in Diagram C.
From Amplier
Tweeter
Diagram A:
Tweeter / Protection Capacitor Wiring
5
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio C7-100ct at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio C7-100ct in the language / languages: English as an attachment in your email.

The manual is 2,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info