701353
5
Zoom out
Zoom in
Previous page
1/16
Next page
Step 6: Connect the speaker wires and
place the W7 into the enclosure
Connect the positive wire to the red terminal and the negative wire to
the black terminal of the W7 (picture 6a). The 13W7 (not shown) has dual
voice coils and must be wired with its coils in series or in parallel. Once
the speaker is wired, gently lower it into the enclosure (picture 6b). This is
difficult on a vertical mounting surface (because of the speaker’s
weight) so you should enlist the help of a second person. If you
need a better grip (or are afraid of smashing your fingers)
you can grasp the inside of the speaker’s mounting flange
(remember, the surround moves out of the way). This tip
is particularly useful with the 13W7.
Step 5: Ready to Install
You are now ready to install the
W7 into its enclosure. The parts are
shown below.
Step 7: Screw it in (12 times)
Line up the screw holes of the frame
with the holes that you have pre-
drilled in your enclosure (you did
pre-drill the holes, right?). The W7
should be attached with heavy
screws such as the ones supplied with
the speaker. This will necessitate pre-
drilling. The use of inferior hardware
(i.e. drywall screws) may lead to
disastrous consequences, so don’t
do it. While holding the surround
back with two fingers (picture 7a),
screw the speaker into the enclosure
(picture 7b). Once all twelve screws
are in place (you did use all twelve,
right?), place the surround back over
the outside of the speaker frame
(picture 7c).
Step 8: Attach O-Ring
Next, take the steel O-Ring that you
removed in step 3, and place it over
the outside of the surround. Push it
down evenly (do not seat one side
first) to make sure it seats the lower
lip of the surround down to the
frame (pictures 8a, 8b).
click
Step 9: Attach Clamp-Ring
Place the seam of the clamp-ring where it will be
least visible in the installation (usually at the bottom
of the speaker). Start one end of the clamp-ring by pressing i t
in firmly (pictures 9a, 9b). Then work your way around from that point
around the speaker, pushing the clamp-ring inward and in the direction
of the circumference of the frame (pictures 9c, 9d). If you have achieved a
tight fit all around, the seam will be small when you reach the starting point
again (pictures 9e, 9f). Check the entire circumference for a tight fit just
to be sure.
Thats it!
You’ve just installed a W7!
5
6a
6b
7a
7b
7c
8a
8b
9a
9b
9c
9d
9f
9e
Be sure that the beveled edge of
the clamp-ring is “pointing towards the front of the
speaker. The clamp-ring is only designed to work in
this orientation.
5
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio 10W7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio 10W7 in the language / languages: English as an attachment in your email.

The manual is 2,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info