507366

JBL TL260 Manual

2
Zoom out
Zoom in
Previous page
1/4
Next page
This TL260 features four rubber feet that enable it to be placed on
a smooth-surfaced floor, such as tile or hardwood. Four metal spikes
are supplied for use when the speaker is to be placed on a carpeted
surface to decouple the speaker from the floor. To insert the spikes,
gently lay the speaker on its side (not its front or back) on a soft,
nonabrasive surface. Each spike screws into the threaded insert in
the center of each rubber foot. Make sure all four spikes are
screwed in completely for stability.
NEVER drag the speaker to move it, as this will damage the spikes,
the feet and/or the wood cabinet itself. Always lift the speaker and
carry it to its new location.
CAUTION: Floorstanding (tower) loudspeakers have a high center of
gravity and may become unstable and tip over during earthquakes
or, if rocked, tipped or improperly positioned. If this is a concern,
these speakers should be anchored to the wall behind them, using
the same procedures and hardware customary for anchoring
bookcases and wall units. The customer is responsible for proper
installation and proper selection of hardware.
SPEAKER SETUP
SPEAKER PLACEMENT
Proper placement of the speakers is an important step in obtaining
the most realistic soundstage possible. These recommendations
are for the optimum placement of the loudspeakers. Use these
placement recommendations as a guide. Slight variations will not
diminish your listening pleasure. The TL260 loudspeaker is video-
shielded and may safely be placed near a television.
MODEL: TL260
WIRING THE SYSTEM
IMPORTANT: Make sure all equipment is turned off
before making any connections.
For speaker connections, use a high-quality speaker wire with
polarity coding. The side of the wire with a ridge or other coding
is usually considered positive polarity (i.e., +).
NOTE: If desired, consult your local JBL dealer about speaker wire
and connection options.
The speakers have coded terminals that accept a variety of wire
connectors. The most common connection is shown in Figure 1.
To ensure proper polarity, connect each + terminal on the back of
the amplifier or receiver to the respective + (red) terminal on each
speaker, as shown in Figure 3. Connect the – (black) terminals in a
similar way. See the owner’s guides that were included with your
amplifier, receiver and television to confirm connection procedures.
IMPORTANT: Do not reverse polarities (i.e., + to –
or – to +) when making connections. Doing so will
cause poor imaging and diminished bass response.
Figure 1. This figure shows how to connect bare wires to the
terminals.
Figure 2. This example shows how to connect bare wires to the
terminals.
Figure 3. Wiring diagram shows polarity connections for one channel
of a stereo or home theater system.
2
26766_TL260 OM_ENG 18/04/06 12:51 Side 2
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL TL260 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL TL260 in the language / languages: English as an attachment in your email.

The manual is 0,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info