507359

JBL DSC 1000 Manual

7
Zoom out
Zoom in
Previous page
1/100
Next page
7
Dolby Pro Logic (Non-Digital) – Line Level (SCS 140 and SCS 146)
Use this installation method for
Dolby Pro Logic applications
(not Dolby Digital, DTS
®
or
other digital processing), where
the receiver/processor is
equipped with a subwoofer
output, or a volume-controlled
preamp (line-) level output:
Use RCA-type patch cords
to connect the line-level
subwoofer output on your
receiver or to amplifier either
the left or right line-level input
on the subwoofer. IMPORTANT:
Do not use the LFE input on the
subwoofer with Dolby Pro Logic
processors. Note: If your
receiver or amplifier has two
subwoofer output jacks then
you can plug the RCA-type
patch cords into both left and
right line-level inputs on the
subwoofer.
Connect each speaker to the
corresponding speaker
terminals on your receiver or
amplifier.
output or subwoofer output
on your receiver or amplifier.
Connect each speaker to the
corresponding speaker
terminals on your receiver or
amplifier.
Make sure that you have
configured your surround-sound
processor for “Subwoofer On.”
The surround receiver should be
configured for 6.1-channel
operation (if available) and the
front left, front right, center and
rear speakers should all be set
to “Small.”
If your receiver allows you to
set the crossover frequency
between the subwoofer and the
main speakers, select either
120Hz or 150Hz, or select the
setting that is the closest
frequency below these.
Dolby Digital or DTS
®
(or Other Digital Surround Mode) Connection
(SCS 140 and SCS 146)
LINE LEVEL IN
LFE INPUT
LFE OUT
L
R
SUBWOOFERRECEIVER
+ –
+ –
+ –
+ –
+ –
+ –
+ –
+ –+ –
Receiver
Subwoofer
Out
Left
Front
Left
Surround
+ –
Right
Front
Right
Surround
Subwoofer
R L
Center
Surround Back
Line-
Level In
Right Surround
Right Front
Left Surround
Left Front
Center
R
L
+ –
Surround Back
+ –
Only in 6.1 systems
Use this installation method for
Dolby Digital, DTS
®
or other
digital surround processors:
Use the line-level input jack
marked “LFE” for the Low-
Frequency Effects channel.
Connect this jack to the LFE
17214 SCS140_146 DSC Multi OM 29/07/03 15:45 Side 7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL DSC 1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL DSC 1000 in the language / languages: English as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info