809288
4
Zoom out
Zoom in
Previous page
1/9
Next page
JBL BASSPRO GO
4
EN
IV. SETTING THE SOUND IN THE
VEHICLE
In Settings Mode, you can adjust the input level, gain, low-pass
crossover, phase control, and bass boost.
FULL RANGE MODE
CONNECT TO VEHICLE
WOOFER MODE
FULL RANGE MODE
SETTINGS MODE SETTINGS MODE SETTINGS MODE
Press & Hold JBL Connect and
Play/Pause buttons for 5s
Press & Hold JBL Connect and
Bluetooth buttons for 5s
Press JBL Connect button to
toggle menu items
INPUT SENSITIVITY
CROSS OVER
GAIN
BASS BOOST
PHASE CONTROL
Press & Hold JBL Connect and
Bluetooth buttons for 5s
Press JBL Connect button to
toggle menu items
INPUT SENSITIVITY
CROSS OVER
GAIN
BASS BOOST
PHASE CONTROL
Press & Hold JBL Connect and
Bluetooth buttons for 5s
Press JBL Connect button to
toggle menu items
INPUT SENSITIVITY
CROSS OVER
GAIN
BASS BOOST
PHASE CONTROL
NOTE: To enter Full-Range Mode from Subwoofer Mode, press and
hold the JBL Connect and Play/Pause buttons for 5 seconds. To switch
back to Subwoofer Mode, repeat the same process.
A. Entering Settings Mode
Press and hold the JBL Connect button and the Bluetooth button
for 5 seconds to enter Settings Mode. The power button will
illuminate in yellow and an alert will sound. Press the JBL Connect
button to toggle between settings. Press the “+” and “–” buttons
to change the value of each setting.
The color of the first LED indicates which setting you are adjusting.
The five white LEDs display the value of the adjustment.
Setting First LED color
Input level (docked in vehicle
only) Blue
Crossover (docked in vehicle in
woofer mode only) Red
Gain (docked in vehicle only) Green
Bass boost Orange
Phase (docked in vehicle in
woofer mode only) Teal
B. Setting the input level
When the BassPro Go is docked in your vehicle, you will need
to set the input level to accept the type of signal it receives from
your source unit. Select level options by pressing the “+” and “–”
buttons.
Signal from source unit LED configuration
LO (low-level preamp outputs)
HI1 (high-level speaker outputs)
HI2 (high-level speaker outputs
if no playback from HI1)
C. Setting the low-pass crossover in subwoofer
mode
The crossover allows only frequencies below a certain point to
reach the speaker in woofer mode. The crossover point you
choose depends on your musical preferences.
Crossover point LED configuration
80Hz
100Hz
120Hz
D. Setting the gain
When the BassPro Go is docked in your vehicle, you will need to
match the gain (input sensitivity) to output of the signal it receives
from your source unit. To set the gain:
1. Start with gain control switch set to 2V.
2. Choose music with substantial bass content and turn the
volume control on your receiver to 75% of its total output.
3. Increase the gain one step at a time by pressing the “+”
button, listening carefully to the bass output, as the LED read
out displays each step. To increase the interval of the gain you
are adjusting, move the gain control switch to 2V, 4V, or 6V as
necessary. If you hear distortion, lower the gain one step at a
time by pressing the “–” button until the distortion disappears.
Input
signal
type
Gain
control
switch
setting
Gain
level LED configuration
Line-level 2V 0.4V - 2V
Line-level 4V 0.8V – 4V
Line-level 6V 1.2V – 6V
High-level 2V 1V – 5V
High-level 4V 2V – 10V
High-level 6V 3V – 15V
JBL BassPro Go_owners manual_SOP_V6.indb 4JBL BassPro Go_owners manual_SOP_V6.indb 4 11/23/2020 5:53:00 PM11/23/2020 5:53:00 PM
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL BassPro Go at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL BassPro Go in the language / languages: English as an attachment in your email.

The manual is 11.53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JBL BassPro Go

JBL BassPro Go User Manual - German - 9 pages

JBL BassPro Go User Manual - Dutch - 9 pages

JBL BassPro Go User Manual - French - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info