809288
3
Zoom out
Zoom in
Previous page
1/9
Next page
EN
3
B. Mounting the speaker in the dock
1. Pull the handle out.
Pull
2. Rest one corner of the speaker on the dock at a slight angle to
get the speaker seated.
3. Rotate the speaker until it is completely in place in the dock.
4. Release the handle to finish securing in place.
NOTE: It will be easiest to connect the wire harness before mounting
the speaker in the dock.
C. Power and Ground Connections in the
vehicle
18" (46cm)
Chassis ground (–)
Remote turn-on (blue)
to stereo REM out
Battery
Fuse holder, 20A fuse
i. Power: Connect the red +12V power wire in the wire harness
to the positive terminal of the vehicle battery. Install a 20A fuse
and fuse holder within 18" (457mm) of the battery.
ii. Ground: Connect the black GND wire in the wire harness to
bare metal of the vehicle’s chassis, such as at a seat belt bolt.
NOTE: If possible, remove any paint from the chassis for best contact.
It is recommended to use a star washer below the ring connector for a
secure connection.
iii. Remote-In: Connect the blue remote turn-on wire in the wire
harness to the “Remote Out” lead of the source unit, if using
low-level signal inputs.
NOTE: 12V ACC turn-on is the preferred method. If you are using
high-level signal inputs (vehicle speaker wires), you can choose to have
the DC offset feature or the audio-sensing feature turn the amplifier on.
You will not have to connect the remote turn-on wire and can terminate
the connection.
D. Power/Protect indicators when connected to
the vehicle
The power button on the control panel indicates the
speaker’s modes of operation.
Illumination color Mode of operation
White Subwoofer mode (in vehicle only)
Green Full-range mode
Red
Protect mode (over/under voltage/short
circuit/amplifier circuit failure/excessive
heat)
Yellow Settings mode
E. Signal input in the vehicle
Line-level inputs: If your source unit offers preamp outputs,
connect them to the RCA inputs in the wire harness. Use front
or rear preamp outputs for full-range operation, or subwoofer
preamp outputs (if available) for subwoofer mode.
12V DC AUDIO
2V 4V 6V
Note: When using low-level signals and remote turn-on lead, set the
“Auto Turn-on” switch to “12V,” and set the speaker’s input level to “LO”
in the settings menu (see “setting the input level”). Set the “Auto-on”
switch to 2V, 4V, or 6V, whichever most closely matches the voltage of
your source unit’s preamp outputs.
High-level inputs: If your source unit does not have line-level
outputs, use the supplied high-level input adapters to connect to
the speaker output wires of your source unit to the RCA inputs in
the wire harness.
Loosen
Screws
Insert
Wires
Tighten
Screws
12V DC AUDIO
NOTE: When using high-level signals, set the “Auto Turn-on” switch to
“DC” (to turn on when it receives battery power) or “AUDIO” (to turn on
when it senses audio signal). Set the input level to “HI1” in the settings
menu (see “setting the input level”). If no sound plays, change the input
level to “HI2”.
F. Connecting the remote bass control in the
vehicle
Plug the remote bass controller into the appropriate input in the
wire harness. Mount the remote in a convenient location, such as
under the dash, using sheet metal screws.
Turn the dial clockwise to increase the bass output, and
counterclockwise to decrease the bass output.
NOTE: Remote bass control will only operate in subwoofer mode.
JBL BassPro Go_owners manual_SOP_V6.indb 3JBL BassPro Go_owners manual_SOP_V6.indb 3 11/23/2020 5:52:59 PM11/23/2020 5:52:59 PM
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL BassPro Go at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL BassPro Go in the language / languages: English as an attachment in your email.

The manual is 11.53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JBL BassPro Go

JBL BassPro Go User Manual - German - 9 pages

JBL BassPro Go User Manual - Dutch - 9 pages

JBL BassPro Go User Manual - French - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info