554865
2
Zoom out
Zoom in
Previous page
1/2
Next page
The UC-82 wireless relay output module MHT51100
2
To extend an existing hard-wired system with wireless detector(s) – enroll
the detector(s) to relay X in mode 4 and once again to relay Y in mode 3. This
way the X relay will work as a detector trigger output, the Y relay as a detector
tamper output and the Low bat terminal will provide low battery indication. Up to
8 detectors can be enrolled to the UC-82 this way and the corresponding output
will be triggered if any of the enrolled detectors reports triggering, tampering or a
low battery.
Using the UC-82 with control panel PG output signals
if the control panel is enrolled to the X relay (in mode 4 by entering 299) then
the X relay works as a control panel PGX output.
if the control panel is enrolled to the Y relay (in mode 4 by entering 299) then
the Y relay works as a control panel PGY output.
Only one control panel PG output can be enrolled to each relay. No other
transmitting devices can be enrolled to a relay already occupied by a control
panel PG output.
Resetting the UC-82 unit
New UC-82 units are sold with factory-default settings (i.e. both relays
have nothing enrolled). To reset a particular relay, do the following:
Repeatedly press the X button (or the Y button for the Y relay) to
achieve the highest number LED flashes (4, or if not possible, then 3).
Then, continuously press the same button and keep pressing it until all
the LEDs flash a couple of times (=Reset). Then release the button.
Technical specifications
Power supply: 10 to 14V DC, standby consumption approx. 20mA
X and Y relay contact rating: max 2A/24V DC or 2A/120V AC
Low bat terminal: max 100mA/24V DC
TMP terminals: max 100mA/24V DC
Communication band: 868 MHz, Oasis protocol
Minimum distance from transmitting devices 1 meter
Operating environment class II general, indoor –10 to +40 °C
Enclosure IP40 EN 60529
Mechanical immunity IK08 EN 50102
Dimensions: 76 x 110 x 33 mm, antenna 35 mm
Can be operated according to ERC REC 70-03
This product complies with ETSI EN 300220, ETS 300683, and EN 60950
Jablotron Ltd. hereby declares that the UC-82 is in compliance with the
essential requirements and other relevant provisions of Directive
1999/5/EC The original of the conformity assessment can be found at
www.jablotron.com
, Technical Support section
Note: Although this product does not contain any harmful materials we
suggest you return the product to the dealer or directly to the producer after
use.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron UC-82 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron UC-82 in the language / languages: English as an attachment in your email.

The manual is 0,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info