554896
9
Zoom out
Zoom in
Previous page
1/12
Next page
Telephone dialer TD-101 / TD-101W - 16 - MDJ512 10 Telephone dialer TD-101 / TD-101W - 9 - MDJ512 10
9. Trouble shooting
It is impossible to stop the dialing function with the Ekey even if it is enabled in the installer
mode. Check if either trigger input IN1 nor IN2 is active (especially if you changed the trigger input
logic to a normally closed contact). Additionally, remember that communication with the monitoring
station can not be stopped until it is finished.
Reaction of the dialer is opposite to what you expect - no reaction when trigger inputs are
activated and the dialer starts to work after inputs are deactivated. In this case the trigger input
logic incorrectly (see item 8.4.).
Dialer does not work when you press the emergency key
F- check that voice message no. 2
was recorded and that there is a telephone number stored in memory
Mem3 or Mem4. Remember
that the emergency function of the
F key can be disabled in the installer mode (see item 8.11.).
Dialer does not work after any kind of triggering - check that it is not in the user or installer
mode (green and yellow LEDs must be off). Press the
Ekey to get back to the stand by mode.
Check if the TD-101 is powered correctly (press the
Ekey and you should hear a beep). Check
also, if the voice messages are recorded and that the telephone numbers are stored in
corresponding memories (see chapter 6).
It is impossible to enter the user or installer mode - it can be entered only if the dialer is not
dialing (red LED must be off). Wait until the dialing is finished or try to stop the dialing with the
Ekey (if stop has been enabled in the installer level).
You need to temporarily switch the dialer off - for example if the device that controls the dialer
triggers is malfunctioning. In such a case enter the user mode with your user code (the green LED
will be switched on), the TD-101 will be disabled. Remember that the user mode can only be
entered in the moment when the dialer is not calling (red LED must be off). Do not forget to switch
the dialer back to stand by (pressing its
Ekey), after the malfunction is repaired
9.1. Emergency reset
In the event, that you forget your user or installer code (or for some other reason), it is possible to
completely reset all parameters of the TD-101. To do this:
disconnect the power and wait 1 minute
reconnect the power (red LED turns on) enter
B
(within 10 seconds after
the power is reconnected)
This procedure resets the factory default settings (UC=1234, IC=1010), all phone numbers and remote
controls (TD-101W only) will be deleted. All the optional functions and parameters will be set to the
factory default setting (see table on page 18 for details).
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron TD-101 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron TD-101 in the language / languages: English as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info