Manual Jablotron JA-82K OASIS (page 4 of 22) (English)

554792

Zoom out

Zoom in

1/22

3.2 Hard-wired inputs on the main board

There are hard-wired input terminals for 01-04 device addresses on the

main board. All hard-wired inputs act identically: double balanced loops which

sense loop stand-by, activation or tampering as follows:

stand-by connected to COM via a 1 kΩ resistor (EOL resistor)

activation connected to COM via a 2k to 6k resistor 

tampering connected to COM via a less than 700  resistor (short-

circuit) or connected to COM via a more than 6k resistor

(loop termination)

12 34

OFF

COM

PGX

PGY

GND

fig. 2 SA-200 magnetic detector connection

12 34

OFF

COM

PGX

PGY

GND

JA-82K control panel installation manual - 4 - MKH51103

fig. 3 JS-20 Largo detector connection

12 34

OFF

COM

PGX

PGY

GND

fig. 4 One-loop connection of JS-25 Combo

12 34

OFF

COM

PGX

PGY

GND

fig. 5 Two-loop connection of JS-25 Combo (01 GBS, 02 PIR)

12 34

OFF

GND

COM

fig. 6 Connection of multiple detectors to the inputs

 The used input zone must be terminated by a 1k resistor in stand-by

state.

 When connecting a trigger contact to the zone, always use a parallel

1k resistor. Thus it is possible to connect up to 5 trigger contacts in

series.

 Tamper contacts should be connected in series (without resistors).

They therefore interrupt the whole loop. You can use an unlimited

amount of tamper contacts which can be combined with trigger

contacts (with parallel resistors).

 The loop (input) reaction can be set. The NATURAL = delayed loop

reaction is set as the factory default.

 If you enrol a wireless device to the hard-wired input address, the

corresponding terminal will be disabled (it will not affect the system).

 If you do not intend to use the hard-wire input or enrol a wireless

device to its address, switch the corresponding DIP switch to the OFF

position (switch off the input).

3.3 Installation of additional hard-wire input

modules

By adding the JA-82C module it is possible to extend the amount of

inputs to fourteen. (addresses 01-14).

All hard-wire inputs behave identically: they are double balanced inputs

which are able to sense stand-by, activation and tampering and for which

examples of connection and conditions stated in Chapter 3.2 apply in full

scope.

When you install the module, relabel the terminal description with a

sticker from the module package (inputs 05-14). Insert plastic spacing posts

on the openings in the module on the connector side and insert the prepared

module to the selected position in the main board.

3.4 Radio module installation

The JA-82R radio module is installed in position 1 (see fig. 1). The

antenna is included in the JA-82R package and it should be screwed on a

plastic post (see fig. 17, pos 5). The antenna connector connects to the pins

the JA-82R module. The module installation enables the system to enroll

up to 50 wireless devices.

3.5 Y,X,V communicator module installation

Screw the selected communicator into position using the supplied

screws as shown in the picture fig. 17.

If y

ou are installing a GSM communicator (Y) and there is a strong GSM

signal in the place of installation, the self-adhesive antenna can be attached

directly to the bottom of the plastic box (see fig. 17). If there is a weak GSM

sig

nal we recommend using some of the available rod antennas.

If you use the combination of a GSM communicator (Y) and a telephone

line communicator (X), install the phone line communicator above the GSM

communicator using the supplied posts.

3.6 Control panel memory chip

The control panel memory chip plugs into its own socket. If you take the

memory unit from the control panel and plug it into another control panel main

board of the same type, the control panel settings (enrolled detectors, codes,

set functions, etc.) are transferred.

Notes:

 communicator settings are not stored in this memory

 do not plug or unplug the memory when the control panel is powered

 when you take the memory unit from a damaged control panel, its

contents may be corrupted. It is therefore highly recommended to

back-up the settings in a PC using OLink software

3.7 Wired keypad connection

The control panel can be operated and programmed by a JA-81E hard-

wired keypad. A screened four-cord flat cable connecting the corresponding

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-82K OASIS in the language / languages: English as an attachment in your email.

The manual is 0,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-82K OASIS

Jablotron JA-82K OASIS User Manual - English - 23 pages

Jablotron JA-82K OASIS Additional guide - English - 1 pages

Jablotron JA-82K OASIS Installation Guide - German - 23 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron JA-82K OASIS Manual

Product: